- 您現在的位置：買賣IC網 > PDF目錄5516 > MAX9633ATA+T (Maxim Integrated Products)IC OPAMP GP 27MHZ LN 8TDFN PDF資料下載
參數資料
| 型號： | MAX9633ATA+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/14頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OPAMP GP 27MHZ LN 8TDFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 放大器類型： | 通用 |
| 電路數： | 2 |
| 轉換速率： | 18 V/µs |
| 增益帶寬積： | 27MHz |
| 電流 - 輸入偏壓： | 42nA |
| 電壓 - 輸入偏移： | 70µV |
| 電流 - 電源： | 3.5mA |
| 電流 - 輸出 / 通道： | 50mA |
| 電壓 - 電源，單路/雙路(±)： | 4.5 V ~ 36 V，±2.25 V ~ 18 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-WDFN 裸露焊盤 |
| 供應商設備封裝： | 8-TDFN-EP（3x3） |
| 包裝： | 帶卷 (TR) |
10
Maxim Integrated
Dual 36V Op Amp for 18-Bit
SAR ADC Front-End
MAX9633
Input Common Mode and Output Swing
The IC’s input common-mode range as well as the out-
put range can swing to the negative rail VEE. These two
features are very important for applications where the
MAX9633 is used with a single supply (VEE connected
to ground). In such a case, being able to swing the input
common-mode to the negative rail offers ground-sensing
capability.
Input Differential Voltage Protection
During normal op-amp operation, the inverting and non-
inverting inputs of the IC are at essentially the same volt-
age. However, either due to fast input voltage transients
or due to other fault conditions, these pins can be forced
to be at two different voltages.
Internal back-to-back diodes protect the inputs from an
excessive differential voltage (Figure 1). Therefore, IN+
and IN- can be any voltage within the range shown in the
Absolute Maximum Ratings. Note the protection time is
still dependent on the package thermal limits.
If the input signal is fast enough to create the internal
diode’s forward bias condition (0.7), the input signal cur-
rent must be limited to 20mA or less. If the input signal
current is not inherently limited, an external input series
resistor can be used to limit the signal input current.
Care should be taken in choosing the input series resis-
tor value, since it degrades the low-noise performance
of the device.
Electrostatic Discharge (ESD)
The IC has built-in circuits to protect from electrostatic
discharge (ESD) events. An ESD event produces a short,
high-voltage pulse that is transformed into a short current
pulse once it discharges through the device. The built-in
protection circuit provides a current path around the op
amp that prevents it from being damaged. The energy
absorbed by the protection circuit is dissipated as heat.
ESD protection is guaranteed up to 6kV with the Human
Body Model (HBM).
The Human Body Model simulates the ESD phenomenon
wherein a charged body directly transfers its accumu-
lated electrostatic charge to the ESD-sensitive device. A
common example of this phenomenon is when a person
accumulates static charge by walking across a carpet
and then transfers all of the charge to an ESD-sensitive
device by touching it.
Power Supplies and Layout
The IC can operate with dual supplies from Q2.25V
to Q18V or with a single supply from +4.5V to +36V
with respect to ground. When used with dual supplies,
bypass both VCC and VEE with their own 0.1FF capaci-
tor to ground. When used with a single supply, bypass
VCC with a 0.1FF capacitor to ground. Careful layout
technique helps optimize performance by decreasing
the amount of stray capacitance at the op amp’s inputs
and outputs. To decrease stray capacitance, minimize
trace lengths by placing external components close to
the op amp’s pins.
For high-frequency designs, ground vias are critical to
provide a ground return path for high-frequency signals
and should be placed around the signal traces and
near the decoupling capacitors. Signal routing should
be short and direct to avoid parasitic effects. Avoid
using right angle connectors since they may introduce
a capacitive discontinuity and ultimately limit the fre-
quency response.
Chip Information
PROCESS: BiCMOS
Figure 1. Input Protection Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| LPSJ601.Z | FUSEHOLDER CLASS J 60A 1 POLE |
| BK1/S506-12.5-R | FUSE 12.5A 250V T-LAG GLASS |
| 8-33457-1 | CONN RING 12-10AWG #10 SOLIS |
| LT301001C | FUSEBLOCK CLASS T 100A 1 POLE |
| GMA-315-R | FUSE .315A 250V FST GLASS UL CSA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9633EVKIT+ | 功能描述:放大器 IC 開發(fā)工具 MAX9633 Eval Kit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| MAX9634EVKIT+ | 功能描述:放大器 IC 開發(fā)工具 MAX9634 Eval Kit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| MAX9634FERS+ | 制造商:Maxim Integrated Products 功能描述:PRECISION , 1UA CURRENT SENSE AMP - Rail/Tube |
| MAX9634FERS+T | 功能描述:電流靈敏放大器 Precision 1uA Current Sense Amp RoHS:否 制造商:Texas Instruments 通道數量: 共模抑制比（最小值）:110 dB 輸入補償電壓:80 uV 電源電壓-最大:5.5 V 電源電壓-最小:2.7 V 電源電流:350 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
| MAX9634FEUK+T | 功能描述:電流靈敏放大器 Precision 1uA Current Sense Amp RoHS:否 制造商:Texas Instruments 通道數量: 共模抑制比（最小值）:110 dB 輸入補償電壓:80 uV 電源電壓-最大:5.5 V 電源電壓-最小:2.7 V 電源電流:350 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
發(fā)布緊急采購，3分鐘左右您將得到回復。