- 您現在的位置：買賣IC網 > PDF目錄2090 > MAX97000EWA+T (Maxim Integrated Products)IC AUDIO SUBSYSTEM 25WLP PDF資料下載
參數資料
| 型號： | MAX97000EWA+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 24/34頁 |
| 文件大小： | 0K |
| 描述： | IC AUDIO SUBSYSTEM 25WLP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 系列： | DirectDrive® |
| 類型： | D 類 |
| 輸出類型： | 1-通道（單聲道），帶立體聲耳機 |
| 在某負載時最大輸出功率 x 通道數量： | 930mW x 1 @ 8 歐姆; 40mW x 2 @ 16 歐姆 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 特點： | 消除爆音，差分輸入，I²C，靜音，關閉，音量控制 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 25-WLP（2.09x2.09） |
| 封裝/外殼： | 25-WFBGA，WLCSP |
| 包裝： | 標準包裝 |
| 其它名稱： | MAX97000EWA+TDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
Audio Subsystem with Mono Class D
Speaker and Class H Headphone Amplifier
MAX97000
30
The slave address with the R/W bit set to 0 indicates that
the master intends to write data to the MAX97000. The
MAX97000 acknowledges receipt of the address byte
during the master-generated 9th SCL pulse.
The second byte transmitted from the master configures
the MAX97000’s internal register address pointer. The
pointer tells the MAX97000 where to write the next byte
of data. An acknowledge pulse is sent by the MAX97000
upon receipt of the address pointer data.
The third byte sent to the MAX97000 contains the data
that is written to the chosen register. An acknowledge
pulse from the MAX97000 signals receipt of the data
byte. The address pointer autoincrements to the next
register address after each received data byte. This
autoincrement feature allows a master to write to sequen-
tial registers within one continuous frame. The master
signals the end of transmission by issuing a STOP condi-
tion. Register addresses greater than 0x09 are reserved.
Do not write to these addresses.
Read Data Format
Send the slave address with the R/W bit set to 1 to initiate
a read operation. The MAX97000 acknowledges receipt
of its slave address by pulling SDA low during the 9th
SCL clock pulse. A START command followed by a read
command resets the address pointer to register 0x00.
The first byte transmitted from the MAX97000 are the
contents of register 0x00. Transmitted data is valid on
the rising edge of SCL. The address pointer autoincre-
ments after each read data byte. This autoincrement
feature allows all registers to be read sequentially within
one continuous frame. A STOP condition can be issued
after any number of read data bytes. If a STOP condition
is issued followed by another read operation, the first
data byte to be read is from register 0x00.
The address pointer can be preset to a specific register
before a read command is issued. The master presets
the address pointer by first sending the MAX97000’s
slave address with the R/W bit set to 0 followed by the
register address. A REPEATED START condition is then
sent followed by the slave address with the R/W bit set
to 1. The MAX97000 then transmits the contents of the
specified register. The address pointer autoincrements
after transmitting the first byte.
The master acknowledges receipt of each read byte
during the acknowledge clock pulse. The master must
acknowledge all correctly received bytes except the last
byte. The final byte must be followed by a not acknowl-
edge from the master and then a STOP condition. Figure
12 illustrates the frame format for reading 1 byte from
the MAX97000. Figure 13 illustrates the frame format for
reading multiple bytes from the MAX97000.
Figure 12. Reading 1 Byte of Data from the MAX97000
Figure 13. Reading n-Bytes of Data from the MAX97000
ACKNOWLEDGE FROM MAX97000
1 BYTE
AUTOINCREMENT INTERNAL
REGISTER ADDRESS POINTER
ACKNOWLEDGE FROM MAX97000
NOT ACKNOWLEDGE FROM MASTER
A
P
A
0
ACKNOWLEDGE FROM MAX97000
R/W
S
R/W
REPEATED START
Sr
1
SLAVE ADDRESS
REGISTER ADDRESS
SLAVE ADDRESS
DATA BYTE
ACKNOWLEDGE FROM MAX97000
1 BYTE
AUTOINCREMENT INTERNAL
REGISTER ADDRESS POINTER
ACKNOWLEDGE FROM MAX97000
A
A P
0
ACKNOWLEDGE FROM MAX97000
R/W
S
R/W
REPEATED START
Sr
1
SLAVE ADDRESS
REGISTER ADDRESS
SLAVE ADDRESS
DATA BYTE
相關PDF資料 |
PDF描述 |
|---|---|
| MAX97001EWP+T | IC AUDIO SUBSYSTEM 20WLP |
| MAX97002EWP+T | IC AUDIO SUBSYSTEM 20WLP |
| MAX97003EWP+T | IC AUDIO SUBSYSTEM LN 20WLP |
| MAX9700AEUB+ | IC AMP AUDIO 1.6W MONO D 10MSOP |
| MAX9701ETG+T | IC AMP AUDIO PWR 2.2W D 24TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX97001EVKIT+ | 功能描述:音頻 IC 開發工具 MAX97001 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| MAX97001EWP+T | 功能描述:音頻放大器 Audio Subsystem w/ Mono Class D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX97002EVKIT+ | 功能描述:音頻 IC 開發工具 MAX97002 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| MAX97002EWP+T | 功能描述:音頻放大器 Audio Subsystem w/ Mono Class D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX97003EVKIT# | 功能描述:音頻 IC 開發工具 MAX97003 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
發布緊急采購，3分鐘左右您將得到回復。