- 您現在的位置：買賣IC網 > PDF目錄2091 > MAX9701ETG+T (Maxim Integrated Products)IC AMP AUDIO PWR 2.2W D 24TQFN PDF資料下載
參數資料
| 型號： | MAX9701ETG+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/22頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP AUDIO PWR 2.2W D 24TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | D 類 |
| 輸出類型： | 2 通道（立體聲） |
| 在某負載時最大輸出功率 x 通道數量： | 2.2W x 2 @ 4 歐姆 |
| 電源電壓： | 2.5 V ~ 5.5 V |
| 特點： | 消除爆音，差分輸入，短路和熱保護，關閉 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 24-TQFN-EP（4x4） |
| 封裝/外殼： | 24-WFQFN 裸露焊盤 |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁
MAX9701
Spread-Spectrum (SSM) Mode
The MAX9701 features a unique spread-spectrum
mode that flattens the wideband spectral components,
improving EMI emissions that may be radiated by the
speaker and cables. This mode is enabled by setting
SYNC = VDD (Table 1). In SSM mode, the switching fre-
quency varies randomly by
±60kHz around the center
frequency (1.2MHz). The modulation scheme remains
the same, but the period of the sawtooth waveform
changes from cycle to cycle (Figure 2). Instead of a
large amount of spectral energy present at multiples of
the switching frequency, the energy is now spread over
a bandwidth that increases with frequency. Above a
few megahertz, the wideband spectrum looks like white
noise for EMI purposes (Figure 3). A proprietary amplifi-
er topology ensures this does not corrupt the noise
floor in the audio bandwidth.
Synchronous Switching Mode
SYNC
The SYNC input allows the MAX9701 to be synchronized
to a user-defined clock, or another Maxim Class D ampli-
fier, creating a fully synchronous system, minimizing
clock intermodulation, and allocating spectral compo-
nents of the switching harmonics to insensitive frequency
bands. Applying a TTL clock signal between 1000kHz
and 1600kHz to SYNC synchronizes the MAX9701. The
period of the SYNC clock can be randomized, allowing
the MAX9701 to be synchronized to another Maxim Class
D amplifier operating in SSM mode.
SYNC_OUT
SYNC_OUT allows several MAX9701s as well as other
Class D amplifiers (such as the MAX9700) to be cas-
caded. The synchronized output minimizes interfer-
ence due to clock intermodulation caused by the
switching spread between single devices. Using
SYNC_OUT, the modulation scheme remains the same
and audio reproduction is not affected by changing the
switching frequency.
Filterless Modulation/Common-Mode Idle
The MAX9701 uses Maxim’s unique modulation scheme
that eliminates the LC filter required by traditional class D
amplifiers, improving efficiency, reducing component
count, conserving board space and system cost.
Conventional Class D amplifiers output a 50% duty cycle,
180
° out-of-phase square wave when no signal is pre-
sent. With no filter, the square wave appears across the
load as a DC voltage, resulting in finite load current,
which increases power consumption especially when
idling. When no signal is present at the input of the
MAX9701, the amplifiers will output an in-phase square
wave as shown in Figure 4. Because the MAX9701 drives
the speaker differentially, the two outputs cancel each
other, resulting in no net idle mode voltage across the
speaker, minimizing power consumption.
Efficiency
Efficiency of a Class D amplifier is due to the switching
operation of the output stage transistors. In a Class D
amplifier, the output transistors act as current-steering
switches and consume negligible additional power.
Any power loss associated with the Class D output
stage is mostly due to the I2R loss of the MOSFET on-
resistance and quiescent-current overhead.
1.3W, Filterless, Stereo Class D Audio
Power Amplifier
12
______________________________________________________________________________________
VIN_ = 0V
OUT_-
OUT_+
VOUT_+ - VOUT_- = 0V
Figure 4. MAX9701 Outputs with No Input Signal
FREQUENCY (MHz)
AMPLITUDE
(dB
μ
V/m)
280
260
240
200
220
80
100
120
140
160
180
60
5.0
10.0
15.0
20.0
25.0
30.0
35.0
40.0
45.0
50.0
0.0
30
300
Figure 3. MAX9701 with 76mm of Speaker Cable with TDK
Common-Mode Choke: TDK ACM4532-801-20-X
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9702ETI+T | IC AMP AUDIO PWR 1.8W D 28TQFN |
| MAX9704ETJ+ | IC AMP AUDIO PWR 16W STER 32TQFN |
| MAX9705DEBC+T | IC AMP AUDIO PWR 2.3W D 12UCSP |
| MAX9707ETX+T | IC AMP AUDIO 2.3W STER+1 36TQFN |
| MAX9708ETN+TD | IC AMP AUDIO PWR 42W STER 56TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9701EUP | 制造商:Maxim Integrated Products 功能描述:1.3W, FILTERLESS, STEREO CLASS D AUDIO POWER - Rail/Tube |
| MAX9701EUP-T | 制造商:Maxim Integrated Products 功能描述:1.3W, FILTERLESS, STEREO CLASS D AUDIO POWER - Tape and Reel |
| MAX9701EVKIT | 功能描述:音頻放大器 Evaluation Kit for the MAX9701 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9702BETI+ | 制造商:Maxim Integrated Products 功能描述:AUD AMP HDPH/SPKR 2CH STEREO 1.8W/0.045W CLS-AB/CLS-D 28TQFN - Rail/Tube |
| MAX9702BETI+T | 制造商:Maxim Integrated Products 功能描述:AUD AMP HDPH/SPKR 2CH STEREO 1.8W/0.045W CLS-AB/CLS-D 28TQFN - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。