參數資料
型號： MAX9720BEBE+T
廠商： Maxim Integrated Products
文件頁數： 5/21頁
文件大小： 0K
描述： IC AMP AUDIO .05W STER AB 16UCSP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 2,500
系列： DirectDrive®, SmartSense™
類型： AB 類
輸出類型： 耳機，2-通道（立體聲）
在某負載時最大輸出功率 x 通道數量： 50mW x 2 @ 32 歐姆
電源電壓： 1.8 V ~ 3.6 V
特點： 消除爆音，短路保護和熱保護，關閉
安裝類型： 表面貼裝
供應商設備封裝： 16-UCSP（2x2）
封裝/外殼： 16-WFBGA，CSPBGA
包裝： 帶卷 (TR)
Mode Selection (MODE_)
SmartSense is controlled by the two mode select
inputs, MODE1 and MODE2. Table 1 shows the operat-
ing modes in relation to the status of the MODE_ inputs.
When MODE1 = MODE2 = low, the device is in low-
power shutdown mode. When MODE1 = high and
MODE2 = low, the device is in forced mono mode. The
right channel is disabled, OUTR goes high impedance,
and the stereo audio input is mixed, and the audio sig-
nal is reproduced on OUTL. SmartSense is disabled in
this mode. When MODE1 = low and MODE2 = high, the
device is in forced stereo mode, and SmartSense is
disabled. When the device detects the presence of a
short BEFORE forced stereo mode is selected, the
device remains in mono mode (Figure 5). When
MODE1 = MODE2 = high, the device is in automatic
detection mode; the operating mode of the device is
determined by SmartSense.
MODE1 is also used to execute a host-controlled
SmartSense routine and reset the ALERT output. On the
rising edge of MODE1, the device invokes a
SmartSense routine. The falling edge of MODE1 resets
the ALERT output to its idle state.
Automatic Detection Mode
A fault condition is defined as a short (under 4
) on
either amplifier output to ground. SmartSense automati-
cally detects and disables the shorted output. The
mixer/attenuator combines the two stereo inputs (INL
and INR), attenuates the resultant signal by a factor of
2, and redirects the audio playback to the remaining
active channel. This allows for full reproduction of a
stereo signal through a single headphone while main-
taining optimum headroom. The mixed mono signal is
output only on the properly loaded channel. If both out-
puts are shorted then both outputs go into a high-
impedance state and no audio playback occurs. In
automatic detection mode (MODE1 = MODE2 = high),
any of the following events trigger a SmartSense test
sequence:
HPS rises above 0.8 x VDD, indicating a headphone
jack has been inserted into the socket.
The 180mA high-side (sourcing) overcurrent thresh-
old is approached, and the output is near GND.
The die temperature exceeds the thermal limit
(+140°C).
Power or shutdown is cycled.
MAX9720
50mW, DirectDrive, Stereo Headphone
Amplifier with SmartSense and Shutdown
______________________________________________________________________________________
13
M1 = L
M2 = L
?
M1 = H
M2 = L
?
M1 = L
M2 = H
?
SHORT
DETECTED
?
STATUS
CHANGE
?
SHDN
SmartSense
FORCED MONO
FORCED STEREO
MONO MODE
STATUS
CHANGE
?
STATUS
CHANGE
?
STATUS
CHANGE
?
STEREO MODE
STATUS
CHANGE
?
N
Y
MAX9720
Figure 5. SmartSense Flow Diagram
MODE1
MODE2
SmartSense
OPERATING
MODE
High
Enabled
Automatic
detection mode
Low
Disabled
Shutdown
High
Low
Disabled
Forced left mono
Low
High
Disabled
Forced stereo
High
Enabled
Host controlled
X
—
Reset ALERT
Table 1. MAX9720 Operating Modes
相關PDF資料
PDF描述
MAX4364ESA/V+ IC AMP AUDIO PWR 1.4W MONO 8SOIC
AD7466BRMZ-REEL IC ADC 12BIT 1.6V LP 8-MSOP
MAX9728BETC+ IC AMP AUDIO .06W STER AB 12TQFN
LTC1096CN8#PBF IC A/D CONV 8BIT SRL IN/OUT 8DIP
MAX9728AEUD+ IC AMP AUDIO .06W STER 14TSSOP
相關代理商/技術參數
參數描述
MAX9720BEUE 制造商:Maxim Integrated Products 功能描述:50MW, DIRECTDRIVE, STEREO HEADPHONE AMPLIFIER - Rail/Tube
MAX9721AEBC 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX9721AEBC-T 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX9721AETC 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX9721AETC+ 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*