- 您現在的位置：買賣IC網 > PDF目錄16779 > MAX98300EVKIT+WLP (Maxim Integrated Products)KIT EVAL FOR MAX98300-WLP PDF資料下載
參數資料
| 型號： | MAX98300EVKIT+WLP |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 14/14頁 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MAX98300-WLP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 放大器類型： | D 類 |
| 輸出類型： | 1-通道（單聲道） |
| 在某負載時最大輸出功率 x 通道數量： | 2.6W x 1 @ 4 歐姆 |
| 電源電壓： | 2.6 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 板類型： | 完全填充 |
| 已用 IC / 零件： | MAX98300 |
| 已供物品： | 板 |
9
Maxim Integrated
Mono 2.6W Class D Amplifier
MAX98300
Shutdown
The MAX98300 features a low-power shutdown mode,
drawing less than 0.1FA of supply current. Drive SHDN
low to put the MAX98300 into shutdown.
Click-and-Pop Suppression
The MAX98300 speaker amplifier features Maxim’s com-
prehensive click-and-pop suppression. During startup,
the click-and-pop suppression circuitry reduces any
audible transient sources internal to the device. When
entering shutdown, the differential speaker outputs ramp
down to PGND quickly and simultaneously.
Applications Information
Filterless Class D Operation
Traditional Class D amplifiers require an output filter.
The filter adds cost, size, and decreases efficiency and
THD+N performance. The MAX98300’s filterless modula-
tion scheme does not require an output filter (Figure 1).
Because the switching frequency of the MAX98300 is
well beyond the bandwidth of most speakers, voice coil
movement due to the switching frequency is very small.
Use a speaker with a series inductance > 10FH. Typical
8I speakers exhibit series inductances in the 20FH to
100FH range.
Component Selection
Speaker Amplifier Power Supply Input (PVDD)
PVDD powers the speaker amplifier. PVDD ranges
from 2.6V to 5.5V. Bypass PVDD with a 0.1FF and 10FF
capacitor to PGND. Apply additional bulk capacitance
at the device if long input traces between PVDD and the
power source are used.
Input Filtering
The input-coupling capacitor (CIN), in conjunction with the
amplifier’s internal input resistance (RIN), forms a high-
pass filter that removes the DC bias from the incoming
signal. These capacitors allow the amplifier to bias the
signal to an optimum DC level.
Assuming zero source impedance with a gain setting of
AV = 6dB, 9dB, or 12dB, CIN is:
IN
3dB
8
C
[ F]
f
=
with a gain setting of AV = 3dB, CIN is:
IN
3dB
5.7
C
[ F]
f
=
with a gain setting of AV = 0dB, CIN is:
IN
3dB
4
C
[ F]
f
=
where f-3dB is the -3dB corner frequency. Use capaci-
tors with adequately low voltage-coefficient for best low-
frequency THD performance.
Layout and Grounding
Proper layout and grounding are essential for optimum
performance. Good grounding improves audio perfor-
mance and prevents switching noise from coupling into
the audio signal.
Use wide, low-resistance output traces. As load imped-
ance decreases, the current drawn from the device
outputs increase. At higher current, the resistance of the
output traces decreases the power delivered to the load.
For example, if 2W is delivered from the speaker output
to a 4I load through a 100mI trace, 49mW is consumed
in the trace. If power is delivered through a 10mI trace,
only 5mW is consumed in the trace. Wide output, supply,
and ground traces also improve the power dissipation of
the device.
The MAX98300 is inherently designed for excellent RF
immunity. For best performance, add ground fills around
all signal traces on top or bottom PCB planes.
The MAX98300 TDFN-EP package features an exposed
thermal pad on its underside. This pad lowers the pack-
age’s thermal resistance by providing a heat conduction
path from the die to the PCB. Connect the exposed ther-
mal pad to the ground plane by using a large pad and
multiple vias.
相關PDF資料 |
PDF描述 |
|---|---|
| RNF-100-1/8-GN-SP | HEAT SHRINK TUBING |
| H3CCH-3418G | IDC CABLE - HKC34H/AE34G/HKC34H |
| H2PXS-1406G | DIP CABLE - HDP14S/AE14G/X |
| RBC22DRTH-S13 | CONN EDGECARD 44POS .100 EXTEND |
| GEC19DRYH-S734 | CONN EDGECARD 38POS DIP .100 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX98300EWL+T | 功能描述:音頻放大器 2W Mono Class D Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX98300SETA+T | 功能描述:音頻放大器 Mono 2W Class D Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX98302ETD+ | 功能描述:IC AMP STER CLASS D 2.4W 14TDFN RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| MAX98302ETD+T | 功能描述:音頻放大器 2W Stereo Class D Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX98302EVKIT+ | 功能描述:音頻 IC 開發工具 MAX98302 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
發布緊急采購，3分鐘左右您將得到回復。