- 您現在的位置：買賣IC網 > PDF目錄2159 > MAX9913EUB+T (Maxim Integrated Products)IC OP AMP R-R I/O 10-UMAX PDF資料下載
參數資料
| 型號： | MAX9913EUB+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/17頁 |
| 文件大小： | 0K |
| 描述： | IC OP AMP R-R I/O 10-UMAX |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 放大器類型： | 通用 |
| 電路數： | 2 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 0.1 V/µs |
| 增益帶寬積： | 200kHz |
| 電流 - 輸入偏壓： | 1pA |
| 電壓 - 輸入偏移： | 200µV |
| 電流 - 電源： | 7µA |
| 電流 - 輸出 / 通道： | 15mA |
| 電壓 - 電源，單路/雙路(±)： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-µMAX |
| 包裝： | 帶卷 (TR) |
MAX9910–MAX9913
200kHz, 4A, Rail-to-Rail
I/O Op Amps with Shutdown
10
______________________________________________________________________________________
rejection ratio of 95dB (typ) allows the devices to be
powered directly from a battery, simplifying design and
extending battery life.
Power-Up Settling Time
The MAX9910–MAX9913 typically require 5s after
power-up. Supply settling time depends on the supply
voltage, the value of the bypass capacitor, the output
impedance of the incoming supply, and any lead resis-
tance or inductance between components. Op-amp
settling time depends primarily on the output voltage
and is slew-rate limited. Figure 3 shows the MAX991_ in
a noninverting voltage follower configuration with the
input held at midsupply. The output settles in approxi-
mately 18s for VDD = 3V (see the Typical Operating
Characteristics for power-up settling time).
Shutdown Mode
The MAX9911/MAX9913 feature active-low shutdown
inputs. The MAX9911/MAX9913 enter shutdown in 2s
(typ) and exit in 30s (typ). The amplifiers’ outputs are
in a high-impedance state in shutdown mode. Drive
SHDN low to enter shutdown. Drive SHDN high to
enable the amplifier. The MAX9913 dual-amplifier fea-
tures separate shutdown inputs. Shut down both ampli-
fiers for the lowest quiescent current.
Power-Supply Bypassing and Layout
To minimize noise, bypass VDD with a 0.1F capacitor
to ground, as close to the pin as possible.
Good layout techniques optimize performance
by decreasing the amount of stray capacitance and
inductance to the op amps’ inputs and outputs.
Minimize stray capacitance and inductance by placing
external components close to the IC.
Figure 1. Rail-to-Rail Output Voltage Range
RAIL-TO-RAIL OUTPUT VOLTAGE RANGE
200
s/div
IN_
3V
0V
1V/div
OUT_
1V/div
Figure 2. Using a Resistor to Isolate a Capacitive Load from
the Op Amp
MAX9910–
MAX9913
RISO
CL
RL
AV =
≈ 1V/V
RL
RL + RISO
Figure 3. Power-Up Test Configuration
MAX991_
100k
100k
OUT
IN-
IN+
0V
5.5V
VDD
VSS
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9917EUB+T | IC OP AMP R-R I/O 10-UMAX |
| MAX9919NASA+T | IC AMP CURRENT SENSE 8SOIC |
| MAX9923TEUB+ | IC AMP CURRENT SENSE 10-MSOP |
| MAX9929FAUA+T | IC AMP CURRENT SENSE 8-UMAX |
| MAX9934TALT+T | IC AMP CURR SENSE LV 6UDFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9914EXK | 制造商:Maxim Integrated Products 功能描述:1MHZ 20+A RAIL-TO-RAIL I/O OP AMP - Rail/Tube |
| MAX9914EXK+ | 制造商:Maxim Integrated Products 功能描述:OP AMP SGL GP R-R I/O 5.5V 5PIN SC-70 - Rail/Tube |
| MAX9914EXK+T | 功能描述:運算放大器 - 運放 1MHz 4uA Rail-Rail Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX9914EXK-T | 功能描述:運算放大器 - 運放 1MHz 4uA Rail-Rail Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX9915EXT | 制造商:Maxim Integrated Products 功能描述:1MHZ 20+A RAIL-TO-RAIL I/O OP AMP - Cut Tape Product |
發布緊急采購，3分鐘左右您將得到回復。