參數資料
型號: MAX9925AUB+
廠商: Maxim Integrated Products
文件頁數: 6/23頁
文件大小: 0K
描述: IC SENSOR INTERFACE VARI 10MSOP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 50
類型: 傳感器接口
輸入類型: 差分
輸出類型: 邏輯
接口: 差分
電流 - 電源: 5mA
安裝類型: 表面貼裝
封裝/外殼: 10-TFSOP,10-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 10-µMAX
包裝: 管件
MAX9924–MAX9927
Zero Crossing
The zero-crossing signal provides true timing informa-
tion for engine-control applications. The zero-voltage
level in the VR sensor signal corresponds to the center
of the gear-tooth and is the most reliable marker for
position/angle-sensing applications. Since the output of
the differential amplifier is level-shifted to the BIAS volt-
age, the zero of the input VR signal is simply BIAS. The
comparator output state controls the status of the input
switch that changes the voltage at its noninverting input
from the adaptive/external threshold level to the BIAS
level. The difference in these two voltages then effec-
tively acts as hysteresis for the comparator, thus pro-
viding noise immunity.
Comparator
The internal comparator is a fast open-drain output
comparator with low input offset voltage and drift. The
comparator precision affects the ability of the signal
chain to resolve small VR sensor signals. An open-drain
output allows the comparator to easily interface to a
variety of C I/O voltages.
When operating the MAX9924/MAX9925/MAX9926 in
Mode C, external hysteresis can be provided by adding
external resistors (see Figures 5 and 8). The high and
low hysteresis thresholds in Mode C can be calculated
using the following equations,
and
Rotational Direction Output
(MAX9926 Only)
For quadrature-connected VR sensors, the open-drain
output DIRN indicates the rotational direction of inputs
IN1 and IN2 based on the output state of COUT1 and
COUT2. DIRN goes high when COUT1 is leading
COUT2, and low when COUT1 is following COUT2.
Applications Information
Bypassing and Layout Considerations
Good power-supply decoupling with high-quality
bypass capacitors is always important for precision
analog circuits. The use of an internal charge pump for
the front-end amplifier makes this more important.
Bypass capacitors create a low-impedance path to
ground for noise present on the power supply.
The minimum impedance of a capacitor is limited to the
effective series resistance (ESR) at the self-resonance
frequency, where the effective series inductance (ESL)
cancels out the capacitance. The ESL of the capacitor
dominates past the self-resonance frequency resulting
in a rise in impedance at high frequencies.
Bypass the power supply of the MAX9924–MAX9927
with multiple capacitor values in parallel to ground. The
use of multiple values ensures that there will be multiple
self-resonance frequencies in the bypass network, low-
ering the combined impedance over frequency. It is
recommended to use low-ESR and low-ESL ceramic
surface-mount capacitors in a parallel combination of
10nF, 0.1F and 1F, with the 10nF placed closest
between the VCC and GND pins. The connection
between these capacitor terminals and the power-sup-
ply pins of the part (both VCC and GND) should be
through wide traces (preferably planes), and without
vias in the high-frequency current path.
V
R
RR
V
TL
BIAS
=
+
×
2
12
V
RV
V
RR
R
V
TH
PULLUP
BIAS
PULLUP
BIAS
=
++
+
1
12
()
Variable Reluctance Sensor Interfaces with
Differential Input and Adaptive Peak Threshold
14
______________________________________________________________________________________
相關PDF資料
PDF描述
MAX9950DCCB+TD IC PMU DUAL 64TQFP
MAX9952FCCB+T IC PMU DUAL 64TQFP
MAXQ2000-RAX+ IC MCU 32K FLASH 68-QFN
MAXQ2010-RFX+ IC MCU 16BIT 64KB FLASH 100-LQFP
MAXQ3120-FFN+ IC MCU 32KB FLASH 80-MQFP
相關代理商/技術參數
參數描述
MAX9925AUB+ 功能描述:接口 - 專用 Variable-Reluctance Sensor Interface RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MAX9925AUB+T 功能描述:接口 - 專用 Variable-Reluctance Sensor Interface RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MAX9926AEE+ 制造商:Maxim Integrated Products 功能描述:- Rail/Tube
MAX9926AEE+T 制造商:Maxim Integrated Products 功能描述:- Tape and Reel
MAX9926FAEE+ 制造商:Maxim Integrated Products 功能描述:- Rail/Tube