參數資料
型號: MAX9945EVKIT+
廠商: Maxim Integrated Products
文件頁數: 13/14頁
文件大小: 0K
描述: EVALUATION KIT FOR MAX9945
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 1
每 IC 通道數: 1 - 單
放大器類型: 通用
輸出類型: 單端,滿擺幅
轉換速率: 2.2 V/µs
電流 - 輸出 / 通道: 25mA
工作溫度: -40°C ~ 125°C
電流供應(主 IC): 400µA
電壓 - 電源,單路/雙路(±): 4.75 V ~ 38 V,±2.4 V ~ 19 V
板類型: 完全填充
已供物品:
已用 IC / 零件: MAX9945
MAX9945
For voltage-output sensors, a noninverting amplifier is
typically used to buffer and/or apply a small gain to, the
input voltage signal. Due to the extremely high imped-
ance of the sensor output, a low input bias current with
a small temperature variation is very important for these
applications.
Power-Supply Decoupling
The MAX9945 operates from a +4.75V to +38V, VEE ref-
erenced power supply. Bypass the power-supply
inputs VCC and VEE to a quiet copper ground plane,
with a 0.1F ceramic capacitor in parallel with a 4.7F
electrolytic capacitor, placed close to the leads.
Layout Techniques
A good layout is critical to obtaining high performance
especially when interfacing with high-impedance sen-
sors. Use shielding techniques to guard against para-
sitic leakage paths. For transimpedance applications,
for example, surround the inverting input, and the
traces connecting to it, with a buffered version of its
own voltage. A convenient source of this voltage is the
noninverting input pin. Pins 1, 5, and 8 on the MAX
package are unconnected, and can be connected to
an analog common potential, or to the driven guard
potential, to reduce leakage on the inverting input.
A good layout guard rail isolates sensitive nodes, such
as the inverting input of the MAX9945 and the traces
connecting to it (see Figure 1), from varying or large volt-
age differentials that otherwise occur in the rest of the
circuit board. This reduces leakage and noise effects,
allowing sensitive measurements to be made accurately.
Take care to also decrease the amount of stray capaci-
tance at the op amp’s inputs to improve stability. To
achieve this, minimize trace lengths and resistor leads
by placing external components as close as possible to
the package. If the sensor is inherently capacitive, or is
connected to the amplifier through a long cable, use a
low-value feedback capacitor to control high-frequency
gain and peaking to stabilize the feedback loop.
38V, Low-Noise, MOS-Input,
Low-Power Op Amp
8
_______________________________________________________________________________________
1
2
8
7
μMAX
3
4
6
5
MAX9945
IN-
IN+
MAX9945
VOUT
+
-
+
Figure 1. Shielding the Inverting Input to Reduce Leakage
MAX9945
IN+
IN-
10k
Ω
10k
Ω
Figure 2. Input Differential Voltage Protection
相關PDF資料
PDF描述
301A022-25/86-0 BOOT MOLDED
IDSD-04-S-06.00-ST8 CABLE ASSEM 8POS
EEC28DREH-S93 CONN EDGECARD 56POS .100 EYELET
LM4040AEX3-3.0+T IC VREF SHUNT PREC 3V SC-70-3
ECM18DTAN-S189 CONN EDGECARD 36POS R/A .156 SLD
相關代理商/技術參數
參數描述
MAX9945EVKIT+ 功能描述:放大器 IC 開發工具 38V MOS-Input Op Amp RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V
MAX9947ETE+ 功能描述:射頻收發器 AISG Interface RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray
MAX9947ETE+T 功能描述:射頻收發器 AISG Interface RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray
MAX9947EVKIT+ 功能描述:射頻開發工具 MAX9947EVKIT+ RoHS:否 制造商:Taiyo Yuden 產品:Wireless Modules 類型:Wireless Audio 工具用于評估:WYSAAVDX7 頻率: 工作電源電壓:3.4 V to 5.5 V
MAX9949DCCB 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: