- 您現在的位置：買賣IC網 > PDF目錄69018 > MAXQ3120-FFN (MAXIM INTEGRATED PRODUCTS INC) 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | MAXQ3120-FFN |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQFP80 |
| 封裝： | 14 X 20 MM, MQFP-80 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 266K |
| 代理商： | MAXQ3120-FFN |
DS1620
6 of 12
1SHOT = One–Shot Mode. If 1SHOT is 1, the DS1620 will perform one temperature conversion upon
reception of the Start Convert T protocol. If 1SHOT is 0, the DS1620 will continuously perform
temperature conversion. This bit is stored in nonvolatile E2 memory, capable of at least 50,000 writes. The
DS1620 is shipped with 1SHOT=0.
For typical thermostat operation, the DS1620 will operate in continuous mode. However, for applications
where only one reading is needed at certain times or to conserve power, the one–shot mode may be used.
Note that the thermostat outputs (THIGH, TLOW, TCOM) will remain in the state they were in after the last
valid temperature conversion cycle when operating in one–shot mode.
OPERATION IN STAND–ALONE MODE
In applications where the DS1620 is used as a simple thermostat, no CPU is required. Since the
temperature limits are nonvolatile, the DS1620 can be programmed prior to insertion in the system. In
order to facilitate operation without a CPU, the CLK/ CONV pin (pin 2) can be used to initiate
conversions. Note that the CPU bit must be set to 0 in the configuration register to use this mode of
operation. Whether CPU=0 or 1, the 3–wire port is active. Setting CPU=1 disables the stand–alone mode.
To use the CLK/ CONV pin to initiate conversions, RST must be low and CLK/ CONV must be high. If
CLK/ CONV is driven low and then brought high in less than 10 ms, one temperature conversion will be
performed and then the DS1620 will return to an idle state. If CLK/ CONV is driven low and remains low,
continuous conversions will take place until CLK/ CONV is brought high again. With the CPU bit set to 0,
the CLK/ CONV will override the 1SHOT bit if it is equal to 1. This means that even if the part is set for
one–shot mode, driving CLK/ CONV low will initiate conversions.
3–WIRE COMMUNICATIONS
The 3–wire bus is comprised of three signals. These are the RST (reset) signal, the CLK (clock) signal,
and the DQ (data) signal. All data transfers are initiated by driving the RST input high. Driving the RST
input low terminates communication. (See Figures 4 and 5.) A clock cycle is a sequence of a falling edge
followed by a rising edge. For data inputs, the data must be valid during the rising edge of a clock cycle.
Data bits are output on the falling edge of the clock and remain valid through the rising edge.
When reading data from the DS1620, the DQ pin goes to a high-impedance state while the clock is high.
Taking RST low will terminate any communication and cause the DQ pin to go to a high-impedance
state.
Data over the 3–wire interface is communicated LSB first. The command set for the 3–wire interface as
shown in Table 4 is as follows.
Read Temperature [AAh]
This command reads the contents of the register which contains the last temperature conversion result.
The next nine clock cycles will output the contents of this register.
Write TH [01h]
This command writes to the TH (HIGH TEMPERATURE) register. After issuing this command the next
nine clock cycles clock in the 9–bit temperature limit which will set the threshold for operation of the
THIGH output.
相關PDF資料 |
PDF描述 |
|---|---|
| MAXQ7666BATM+ | RISC MICROCONTROLLER, QCC48 |
| MB-91110PMT2 | 32-BIT, MROM, 50 MHz, RISC MICROCONTROLLER, PQFP144 |
| MB86602CPF | SCSI BUS CONTROLLER, PQFP100 |
| MB86604LPFV | SCSI BUS CONTROLLER, PQFP100 |
| MB86605PMT | SCSI BUS CONTROLLER, PQFP144 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAXQ3120-FFN+ | 功能描述:IC MCU 32KB FLASH 80-MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MAXQ® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:260 系列:73S12xx 核心處理器:80515 芯體尺寸:8-位 速度:24MHz 連通性:I²C，智能卡，UART/USART，USB 外圍設備:LED，POR，WDT 輸入/輸出數:9 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-VFQFN 裸露焊盤 包裝:管件 |
| MAXQ3120-KIT | 制造商:Maxim Integrated Products 功能描述:MAXQ3120 EVALUATION KIT - Bulk |
| MAXQ314 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single-Phase Power-Measurement IC with I2C Interface |
| MAXQ314+ | 功能描述:16位微控制器 - MCU Integrated Circuits (ICs) PMIC - Energy Metering - IC PWR MEASUREMENT 1PH 10-TQFN RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| MAXQ314-KIT | 功能描述:開發板和工具包 - 其他處理器 MAXQ314 Eval Kit RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓: |
發布緊急采購，3分鐘左右您將得到回復。