- 您現在的位置：買賣IC網 > PDF目錄377878 > MB15E06PV1 (FUJITSU LTD) Single Serial Input PLL Frequency Synthesizer On-Chip 2.5 GHz Prescaler PDF資料下載
參數資料
| 型號： | MB15E06PV1 |
| 廠商： | FUJITSU LTD |
| 元件分類： | XO, clock |
| 英文描述： | Single Serial Input PLL Frequency Synthesizer On-Chip 2.5 GHz Prescaler |
| 中文描述： | PLL FREQUENCY SYNTHESIZER, 2500 MHz, PBCC16 |
| 封裝： | PLASTIC, BCC-16 |
| 文件頁數： | 10/23頁 |
| 文件大?。?/td> | 223K |
| 代理商： | MB15E06PV1 |
MB15E06
10
When designing a synthesizer, the FC pin setting depends on the VCO and LPF characteristics.
3. Power Saving Mode (Intermittent Mode Control Circuit)
Setting a PS pin to Low, the IC enters into power saving mode resultatly current sonsumption can be limited to
10
μ
A (max.) . Setting PS pin to High, power saving mode is released so that the IC works normally.
In addition, the intermittent operation control circuit is included which helps smooth start up from the power
saving mode. In general, the power consumption can be saved by the intermittent operation that powering down
or waking up the synthesizer. Such case, if the PLL is powered up uncontrolled, the resulting phase comparator
output signal is unpredictable due to an undefined phase relation between reference frequency (f
r
) and compar-
ison frequency (f
p
) and may in the worst case take longer time for lock up of the loop.
To prevent this, the intermittent operation control circuit enforces a limited error signal output of the phase detector
during power up, thus keeping the loop locked.
During the power saving mode, the corresponding section except for indispensable circuit for the power saving
function stops working, then current consumption is reduced to 10
μ
A (max.) .
Note :
While the power saving mode is executed, ZC pin should be set at “H” or open. If ZC is set at “L”
during power saving mode, approximately 10
μ
A current flows.
PS pin must be set “L” at Power-ON.
The power saving mode can be released (PS : L
→
H) 1
μ
s later after power supply remains stable.
During the power saving mode, it is possible to input the serial data.
(1)
(2)
LPF Output Voltage
VCO
Output
Frequency
Large
High
* : When the LPF and VCO characteristics are
similar to (1) , set FC bit high.
* : When the VCO characteristics are similar to
(2) , set FC bit low.
ON
OFF
V
CC
Clock
Data
LE
PS
(1)
(2)
(3)
t
V
≥
1
μ
s
t
PS
≥
100 ns
(1) PS
=
L (power saving mode) at Power ON
(2) Set serial data 1
μ
s later after power supply remains stable (V
CC
≥
2.2 V) .
(3) Release power saving mode (PS : L
→
H) 100 ns later after setting serial data.
相關PDF資料 |
PDF描述 |
|---|---|
| MB15E06SR | Single Serial Input PLL Frequency Synthesizer On-chip 3.0 GHz Prescaler |
| MB15E06SRPFT | Single Serial Input PLL Frequency Synthesizer On-chip 3.0 GHz Prescaler |
| MB15E06SRPV1 | Single Serial Input PLL Frequency Synthesizer On-chip 3.0 GHz Prescaler |
| MB15E06 | Serial Input PLL Frequency Synthesizer(串行輸入PLL頻率合成器) |
| MB15E07L | Single Serial Input PLL Frequency Synthesizer On-Chip 2.5 GHz Prescaler |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB15E06SR | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:Single Serial Input PLL Frequency Synthesizer On-chip 3.0 GHz Prescaler |
| MB15E06SRPFT | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:Single Serial Input PLL Frequency Synthesizer On-chip 3.0 GHz Prescaler |
| MB15E06SRPFT-G-BNDE1 | 制造商:FUJITSU 功能描述: |
| MB15E06SRPFT-G-BND-ERE1 | 功能描述:IC SYNTHESIZR PLL 3.0GHZ 16TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 產品變化通告:Product Discontinuation 04/May/2011 標準包裝:96 系列:- 類型:時鐘倍頻器，零延遲緩沖器 PLL:帶旁路 輸入:LVTTL 輸出:LVTTL 電路數:1 比率 - 輸入:輸出:1:8 差分 - 輸入:輸出:無/無 頻率 - 最大:133.3MHz 除法器/乘法器:是/無 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:管件 其它名稱:23S08-5HPGG |
| MB15E06SRPV1 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:Single Serial Input PLL Frequency Synthesizer On-chip 3.0 GHz Prescaler |
發布緊急采購，3分鐘左右您將得到回復。