- 您現在的位置：買賣IC網 > PDF目錄377879 > MB2146-303A (Fujitsu Limited) 8-bit Microcontrollers PDF資料下載
參數資料
| 型號： | MB2146-303A |
| 廠商： | Fujitsu Limited |
| 英文描述： | 8-bit Microcontrollers |
| 中文描述： | 8位微控制器 |
| 文件頁數： | 14/64頁 |
| 文件大?。?/td> | 797K |
| 代理商： | MB2146-303A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
MB95130MB Series
14
■
HANDLING DEVICES
Preventing latch-up
Care must be taken to ensure that maximum voltage ratings are not exceeded when the devices are used.
Latch-up may occur on CMOS ICs if voltage higher than V
CC
or lower than V
SS
is applied to input and output pins
other than medium- and high-withstand voltage pins or if voltage higher than the rating voltage is applied between
V
CC
pin and V
SS
pin.
When latch-up occurs, power supply current increases rapidly and might thermally damage elements.
Also, take care to prevent the analog power supply voltage (AV
CC
) and analog input voltage from exceeding the
digital power supply voltage (V
CC
) when the analog system power supply is turned on or off.
Stable supply voltage
Supply voltage should be stabilized.
A sudden change in power supply voltage may cause a malfunction even within the guaranteed operating range
of the V
CC
power supply voltage.
For stabilization, in principle, keep the variation in V
CC
ripple (p-p value) in a commercial frequency range
(50 / 60 Hz) not to exceed 10
%
of the standard V
CC
value and suppress the voltage variation so that the transient
variation rate does not exceed 0.1 V/ms during a momentary change such as when the power supply is switched.
Precautions for use of external clock
Even when an external clock is used, oscillation stabilization wait time is required for power-on reset, wake-up
from the sub clock mode or stop mode.
PIN CONNECTION
Treatment of unused pins
Leaving unused input pins unconnected can cause abnormal operation or latch-up, leading to permanent
damage. Unused input pins should always be pulled up or down through resistance of at least 2 k
.
Any unused input/output pins may be set to the output mode and left open, or set to the input mode and treated
the same as unused input pins. If there is any unused output pin, make it open.
Treatment of power supply pins on A/D converter
Connect to be AV
CC
=
V
CC
and AV
SS
=
V
SS
even if the A/D converter is not in use.
Noise riding on the AV
CC
pin may cause accuracy degradation. So, connect approx. 0.1
μ
F ceramic capacitor
as a bypass capacitor between AV
CC
and AV
SS
pins in the vicinity of this device.
Power Supply Pins
In products with multiple V
CC
or V
SS
pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, all the pins must be connected to external power
supply and a ground line to lower the electro-magnetic emission level, to prevent abnormal operation of strobe
signals caused by the rise in the ground level, and to conform to the total output current rating. Moreover, connect
the current supply source with the V
CC
and V
SS
pins of this device at the low impedance.
It is also advisable to connect a ceramic bypass capacitor of approximately 0.1
μ
F between V
CC
and V
SS
pins
near this device.
Mode pin (MOD)
Connect the mode pin directly to V
CC
or V
SS
pins.
To prevent the device unintentionally entering the test mode due to noise, lay out the printed circuit board so as
to minimize the distance from the mode pins to V
CC
or V
SS
pins and to provide a low-impedance connection.
相關PDF資料 |
PDF描述 |
|---|---|
| MB2146-303 | 8-bit Proprietary Microcontrollers |
| MB3514 | RGB Encoder(RGB編碼器) |
| MB3778 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| MB3778P | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| MB3778PF | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB2146-303A-E | 制造商:FUJITSU 功能描述:KIT MCU BOARD 8FX FAMILY 制造商:FUJITSU 功能描述:F2MC-8FX, MB95FV100D-103, EVAL BOARD; Silicon Manufacturer:Fujitsu; Silicon Family Name:F2MC-8FX; Kit Contents:Board; Features:LVD2 Detection Voltage Selector Jumper Plug, BGM Adapter Connector ;RoHS Compliant: NA |
| MB2146-401 | 制造商:FUJITSU 功能描述:KIT EVALUATION BOARD 8FX FAMILY |
| MB2146-401-01A | 功能描述:KIT STARTER F2MC-8FX 3V RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:F²MC-8FX 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，線纜，元件，CD，PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF) |
| MB2146-401-03A | 功能描述:KIT STARTER F2MC-8FX 5V RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:F²MC-8FX 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，線纜，元件，CD，PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF) |
| MB2146-410A-01-E | 功能描述:KIT STARTER MB95200/210H SERIES RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:F²MC-8FX 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，線纜，元件，CD，PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。