- 您現在的位置：買賣IC網 > PDF目錄377880 > MB3793-30 (Fujitsu Limited) Power Supply Monitor with Watch-Dog Timer(帶看門狗定時器的電源監視器) PDF資料下載
參數資料
| 型號： | MB3793-30 |
| 廠商： | Fujitsu Limited |
| 英文描述： | Power Supply Monitor with Watch-Dog Timer(帶看門狗定時器的電源監視器) |
| 中文描述： | 電源監視器看門狗定時器（帶看門狗定時器的電源監視器） |
| 文件頁數： | 10/20頁 |
| 文件大?。?/td> | 182K |
| 代理商： | MB3793-30 |
10
MB3793
-42/30
5. Clock pulse input (Positive clock pulse)
I
OPERATION SEQUENCE
The operation sequence is explained by using Timing Chart 1.
The following item numbers correspond to the numbers in Timing Chart 1.
(1) When the power voltage (V
CC
(2) When V
CC
exceeds the rising-edge detection voltage (V
V
SH
is about 4.3 V in the MB3793-42 and 3. 07 V in the MB3793-30.
(3) When the voltage at the CTP pin setting the power-on reset hold time exceeds the threshold voltage (V
the voltage at the RESET pin changes to High level to start charging of the watchdog-timer monitoring time setting capacitance (C
Vth is about 3.6 V in the MB3793-42 and 2.4 V in the MB3793-30.
The power-on reset hold time (t
PR
) can be calculated by the following equation.
t
PR
(ms)
≈
A x C
TP
(
μ
F)
Where, A is about 1300 in the MB3793-42 and 750 in the MB3793-30.
(4) When the voltage at the CTW pin setting the monitoring time reaches High level (V
is about 1.24 V (reference value) in both the MB3793-42 and MB3793-30.
(5) When clock pulses are input to the CK2 pin during C
TW
discharging after clock pulses are input to the CK1 pin—positive-edge trigger,
C
TW
switches to charging.
(6) If clock pulse input does not occur at either the CK1 or CK2 clock pins during the watchdog-timer monitoring time (t
falls below Low level (V
L
), a reset signal is output, and the voltage at the RESET pin changes to Low level. V
the MB3793-42 and MB3793-30.
t
WD
can be calculated from the following equation.
t
WD
(ms)
≈
B x C
TW
(
μ
F) + C x C
TP
(
μ
F)
Where, B is about 1500 in the MB3793-42 and 1600 in the MB3793-30. C is about 3 in the MB3793-42 and 4 in the MB3793-30; it is
much smaller than B.
) reaches about 0.8 V (V
CCL
), a reset signal is output.
), charging of power-on reset hold time setting capacitance (C
SH
TP
) is started.
th
), resetting is canceled and
TW
).
H
), C
TW
switches to discharging from charging. V
H
WD
), the CTW voltage
is about 0.24 V in both
L
Hence, when ——
t
WD
(ms)
≤
10, the calculation can be simplified as follows:
B x C
TW
(
μ
F)
≈
CTW
V
L
V
H
CK1
CK2
b
The MB3793 watchdog timer monitors Clock 1 (CK1) and Clock 2 (CK2) pulses alternately. When a CK2 pulse
is detected after detecting a CK1 pulse, the monitoring time setting capacity (C
TW
) switches to charging from
discharging.
When two consecutive pulses occur on one side of this alternation before switching, the second pulse is ignored.
In the above figure, pulses aand bare ignored.
a
相關PDF資料 |
PDF描述 |
|---|---|
| MB3793-42 | Power Supply Monitor with Watch-Dog Timer(帶看門狗定時器的電源監視器) |
| MB3793-37A | Power Voltage Monitoring IC with Watchdog Timer |
| MB3793-37PF | Power Voltage Monitoring IC with Watchdog Timer |
| MB3793-37PNF | Power Voltage Monitoring IC with Watchdog Timer |
| MB3793 | POWER-VOLTAGE MONITORING IC WITH WATCHDOG TIMER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB3793-30A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:Power Voltage Monitoring IC with Watchdog Timer |
| MB3793-30APF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:Power Voltage Monitoring IC with Watchdog Timer |
| MB3793-30APF-E1 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:Power Voltage Monitoring IC with Watchdog Timer |
| MB3793-30APFV | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:Power Voltage Monitoring IC with Watchdog Timer |
| MB3793-30APFV-E1 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:Power Voltage Monitoring IC with Watchdog Timer |
發布緊急采購，3分鐘左右您將得到回復。