- 您現在的位置：買賣IC網 > PDF目錄69018 > MB881631CPN-G-ERE1 (FUJITSU LTD) 42 MHz, OTHER CLOCK GENERATOR, PDSO8 PDF資料下載
參數資料
| 型號： | MB881631CPN-G-ERE1 |
| 廠商： | FUJITSU LTD |
| 元件分類： | 時鐘產生/分配 |
| 英文描述： | 42 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| 封裝： | 2 X 2 MM, 0.75 MM HEIGHT, 0.50 MM PITCH, PLASTIC, SON-8 |
| 文件頁數： | 14/19頁 |
| 文件大小： | 685K |
| 代理商： | MB881631CPN-G-ERE1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁
MB88163
4
DS04-29137-3E
■ HANDLING DEVICES
(1) Preventing Latch-up
A latch-up can occur if, on this device, (a) a voltage higher than power supply voltage or a voltage lower than
GND is applied to an input or output pin or (b) a voltage higher than the rating is applied between power
supply pin and GND pin. The latch-up, if it occurs, significantly increases the power supply current and may
cause thermal destruction of an element. When you use this device, be very careful not to exceed the
maximum rating.
(2) Handling unused pins
Do not leave an unused input pin open, since it may cause a malfunction. Handle by, using a pull-up or pull-
down resistor.
(3) The attention when the external clock is used
Input the clock to XIN pin, and XOUT pin should be opened when you use the external clock.
Please pay attention so that an overshoot and an undershoot do not occur to an input clock of XIN pin.
(4) Power supply pins
Please design connecting the power supply pin of this device by as low impedance as possible from the
current supply source.
We recommend connecting electrolytic capacitor (about 10
μF) and the ceramic capacitor (about 0.01 μF)
in parallel between power supply and GND near the device, as a bypass capacitor.
(5) Crystal oscillator circuit
Noise near the XIN and XOUT pins may cause the device to malfunction. Design printed circuit boards so
that electric wiring of XIN or XOUT pin and resonator (or ceramic oscillator) do not intersect other wiring.
Design the printed circuit board that surrounds the XIN and XOUT pins with ground.
相關PDF資料 |
PDF描述 |
|---|---|
| MB89123APFM | 8-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PQFP48 |
| MB89202P-SH | 8-BIT, MROM, 12.5 MHz, MICROCONTROLLER, PDIP32 |
| MB89F202RAP-SH | 8-BIT, FLASH, 12.5 MHz, MICROCONTROLLER, PDIP32 |
| MB89F202RAYPFV | 8-BIT, FLASH, 12.5 MHz, MICROCONTROLLER, PDSO34 |
| MB89352PSH | SCSI BUS CONTROLLER, PDIP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB88181PFT-G-001-BNDE1 | 功能描述:IC SSCG EMI RED 20-TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 產品變化通告:Product Discontinuation 04/May/2011 標準包裝:96 系列:- 類型:時鐘倍頻器，零延遲緩沖器 PLL:帶旁路 輸入:LVTTL 輸出:LVTTL 電路數:1 比率 - 輸入:輸出:1:8 差分 - 輸入:輸出:無/無 頻率 - 最大:133.3MHz 除法器/乘法器:是/無 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:管件 其它名稱:23S08-5HPGG |
| MB88182 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:Spread Spectrum Clock Generator |
| MB881U3-1SA | 制造商:Icy Dock 功能描述:HDD ADAPTER W/ DOCKING STAND 2.5 INCH/3.5 INCH SATA/IDE 制造商:ICY DOCK 功能描述:HDD ADAPTER W/ DOCKING STAND 2.5 INCH/3.5 INCH SATA/IDE |
| MB88200 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:CMOS SINGLE-CHIP 4-BIT MICROCOMPUTER WITH A/D CONVERTER |
| MB88201 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:CMOS SINGLE-CHIP 4-BIT MICROCOMPUTER WITH A/D CONVERTER |
發布緊急采購，3分鐘左右您將得到回復。