參數資料
型號： MB89144AP
廠商： FUJITSU LTD
元件分類： 微控制器/微處理器
英文描述： 8-bit Proprietary Microcontroller
中文描述： 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP64
封裝： SHRINK, PLASTIC, DIP-64
文件頁數： 11/38頁
文件大?。?/td> 518K
代理商： MB89144AP
11
MB89143A/144A
I
HANDLING DEVICES
1. Preventing Latchup
Latchup may occur on CMOS ICs if voltage higher than V
CC
or lower than V
SS
is applied to input and output pins
other than medium- to high-voltage pins or if higher than the voltage which shows on “1. Absolute Maximum
Ratings” in section “
I
Electrical Characteristics” is applied between V
CC
and V
SS
. (However, up to 7.0 V can be
applied to P31/INT1 pin, regardless of V
CC
.)
When latchup occurs, power supply current increases rapidly and might thermally damage elements. When
using, take great care not to exceed the absolute maximum ratings.
Also, take care to prevent the analog power supply (AVR) and analog input from exceeding the digital power
supply (V
CC
) when the analog system power supply is turned on and off.
2. Treatment of Unused Input Pins
Leaving unused input pins open could cause malfunctions. They should be connected to a pull-up or pull-down
resistor.
3. Treatment of Power Supply Pins on Microcontrollers with A/D and D/A Converters
Connect to be AV
SS
= AVR = V
SS
even if the A/D and D/A converters are not in use.
4. Treatment of N.C. Pins
Be sure to leave (internally connected) N.C. pins open.
5. Power Supply Voltage Fluctuations
Although V
CC
power supply voltage is assured to operate within the rated range, a rapid fluctuation of the voltage
could cause malfunctions, even if it occurs within the rated range. Stabilizing voltage supplied to the IC is
therefore important. As stabilization guidelines, it is recommended to control power so that V
CC
ripple fluctuations
(P-P value) will be less than 10% of the standard V
CC
value at the commercial frequency(50 to 60 Hz) and the
transient fluctuation rate will be less than 0.1 V/ms at the time of a momentary fluctuation such as when power
is switched.
6. Precautions when Using an External Clock
Even when an external clock is used, oscillation stabilization time is required for power-on reset and wake-up
from stop mode.
相關PDF資料
PDF描述
MB89146V1P-SH 8-bit Proprietary Microcontroller
MB89146V1PF 8-bit Proprietary Microcontroller
MB89146V2P-SH 8-bit Proprietary Microcontroller
MB89146V2PF 8-bit Proprietary Microcontroller
MB89155PF 8-bit Proprietary Microcontroller
相關代理商/技術參數
參數描述
MB89144AP-SH 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller CMOS
MB89145 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller
MB89145V1PF 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller
MB89145V1P-SH 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller
MB89145V2PF 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*