- 您現在的位置：買賣IC網 > PDF目錄377900 > MB89P133 (Fujitsu Limited) 8-bit Proprietary Microcontroller PDF資料下載
參數資料
| 型號： | MB89P133 |
| 廠商： | Fujitsu Limited |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8-bit Proprietary Microcontroller |
| 中文描述： | 8位微控制器專有 |
| 文件頁數： | 10/47頁 |
| 文件大?。?/td> | 593K |
| 代理商： | MB89P133 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
MB89120/120A Series
10
I
HANDLING DEVICES
1.
Preventing Latchup
Latchup may occur on CMOS ICs if voltage higher than V
CC
or lower than V
SS
is applied to input and output pins
other than medium- and high- voltage pins, or if higher than the voltage which shows on “1. Absolute Maximum
Ratings” in “
I
ELECTRICAL CHARACTERISTICS” is applied between V
CC
and V
SS
.
When latchup occurs, power supply current increases rapidly, and might thermally damage elements. When
using, take great care not to exceed the absolute maximum ratings.
Also, take care to prevent the analog power supply (AV
CC
and AVR) and analog input from exceeding the digital
power supply (V
CC
) when the analog system power supply is turned on and off.
Treatment of Unused Input Pins
2.
Leaving unused input pins open could cause malfunctions. They should be connected to pull-up or pull-down
resistor.
Treatment of N.C. Pins
3.
Be sure to leave (internally connected) N.C. pins open.
Power Supply Voltage Fluctuations
4.
Although operation is assured within the rated range of V
CC
power supply voltage, a rapid fluctuation of the
voltage could cause malfunctions, even if it occurs within the rated range. Stabilizing voltage supplied to the IC
is therefore important. As stabilization guidelines, it is recommended to control power so that V
CC
ripple fluctu-
ations (P-P value) will be less than 10
%
of the standard V
CC
value at the commercial frequency (50 to 60 Hz)
and the transient fluctuation rate will be less than 0.1 V/ms at the time of a momentary fluctuation such as when
power is switched.
Precautions when Using an External Clock
5.
When an external clock is used, oscillation stabilization time is required even for power-on reset (optional) and
release from stop mode.
Turning on the supply voltage (only for the MB89P135A)
6.
When the power supply is turned on if MB89P135A is used, power on sharply up to 2.0 V within 13 clock cycles
after starting of oscillation.
Further, various option may be set, if power supply up to keep this condition.
相關PDF資料 |
PDF描述 |
|---|---|
| MB89P133A-201 | 8-bit Proprietary Microcontroller |
| MB89P133APFM-201 | 8-bit Proprietary Microcontroller |
| MB89P135APFM | 8-bit Proprietary Microcontroller |
| MB89120A | 8-bit Proprietary Microcontroller |
| MB89121PFM | 8-bit Proprietary Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB89P133A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89P133A-201 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89P133AP-201 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89P133APFM-201 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89P135 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。