- 您現在的位置：買賣IC網 > PDF目錄377903 > MB89P175A (Fujitsu Limited) 8-Bit Proprietary Microcontroller(8位專用微控制器) PDF資料下載
參數資料
| 型號： | MB89P175A |
| 廠商： | Fujitsu Limited |
| 英文描述： | 8-Bit Proprietary Microcontroller(8位專用微控制器) |
| 中文描述： | 8位微控制器專利（8位專用微控制器） |
| 文件頁數： | 19/44頁 |
| 文件大?。?/td> | 686K |
| 代理商： | MB89P175A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
MB89170/170A Series
19
The RP indicates the address of the register bank currently in use. The relationship between the pointer contents
and the actual address is based on the conversion rule illustrated below.
The CCR consists of bits indicating the results of arithmetic operations and the contents of transfer data, and
bits for control of CPU operations at the time of an interrupt.
H-flag:
Set to ‘1’ when a carry or a borrow from bit 3 to bit 4 occurs as a result of arithmetic operation. Cleared
to ‘0’ otherwise. This flag is for decimal adjustment instructions.
I-flag:
Interrupt is enabled when this flag is set to 1’. Interrupt is disabled when the flag is cleared to 0’. Cleared
to ‘0’ at the reset.
IL1, 0:
Indicates the level of the interrupt currently allowed. Processes an interrupt only if its request level is
higher than the value indicated by this bit.
N-flag:
Set to ‘1’ if the MSB becomes ‘1’ as the result of an arithmetic operation. Cleared to ‘0’ otherwise.
Z-flag:
Set to ‘1’ when an arithmetic operation results in ‘0’. Cleared to ‘0’ otherwise.
V-flag:
Set to ‘1’ if the complement on 2 overflows as a result of an arithmetic operation. Cleared to ‘0’ if the
overflow does not occur.
C-flag:
Set to ‘1’ when a carry or a borrow from bit 7 occurs as a result of an arithmetic operation. Cleared to
‘0’ otherwise. Set to the shift-out value in the case of a shift instruction.
IL1
IL0
Interrupt level
High-low
0
0
1
High
Low
0
1
1
0
2
1
1
3
Rule for Conversion of Actual Addresses of the General-purpose Register Area
“0”
↓
A15
“0”
↓
A14
“0”
↓
A13
“0”
↓
A12
“0”
↓
A11
“0”
↓
A10
“0”
↓
A9
“1”
↓
A8
R4
↓
A7
R3
↓
A6
R2
↓
A5
R1
↓
A4
R0
↓
A3
b2
↓
A2
b1
↓
A1
b0
↓
A0
Lower OP codes
RP
Generated addresses
相關PDF資料 |
PDF描述 |
|---|---|
| MB89174A | 8-Bit Proprietary Microcontroller(8位專用微控制器) |
| MB89174L | Hex Inverters 14-CDIP -55 to 125 |
| MB89170 | Replaced by SN54LS03 : Quadruple 2-Input Positive-NAND Buffers With Open-Collect 20-LCCC -55 to 125 |
| MB89180L | 8-bit Proprietary Microcontroller |
| MB89183L | 8-bit Proprietary Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB89P175APF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89P185 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89P185-103PMC-GE1 | 制造商:FUJITSU 功能描述: |
| MB89P185PF-101 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89P185PF-102 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。