參數資料
型號： MB90223
廠商： Fujitsu Limited
英文描述： 8-Bit Proprietary Microcontroller(8位專用微控制器)
中文描述： 8位微控制器專利（8位專用微控制器）
文件頁數： 16/105頁
文件大?。?/td> 1130K
代理商： MB90223
MB90220 Series
16
I
HANDLING DEVICES
1. Preventing Latchup
CMOS ICs may cause latchup when a voltage higher than V
CC
or lower than V
SS
is applied to input or output
pins other than medium-and high-voltage pins, or when a voltage exceeding the rating is applied between V
CC
and V
SS
.
If latch-up occurs, the power supply current increases rapidly, sometimes resulting in thermal breakdown of the
device. Use meticulous care not to let any voltage exceed the maximum rating.
Also, take care to prevent the analog power supply (AV
CC
and AVRH) and analog input from exceeding the
digital power supply (V
CC
) when the analog system power supply is turned on and off.
2. Treatment of Unused Input Pins
Leaving unused input pins open could cause malfunctions. They should be connected to a pull-up or pull-down
resistor.
3. Treatment of Pins when A/D is not Used
Connect to be AV
CC
= AVRH = V
CC
and AV
SS
= AVRL = V
SS
even if the A/D converter is not in use.
4. Precautions when Using an External Input
To reset the internal circuit properly by the “L” level input to the RST pin, the “L” level input to the RST pin must
be maintained for at least five machine cycles. Pay attention to it if the chip uses external clock input.
5. V
CC
and V
SS
Pins
Apply equal potential to the V
CC
and V
SS
pins.
6. Supply Voltage Variation
The operation assurance range for the V
CC
supply voltage is as given in the ratings. However, sudden changes
in the supply voltage can cause misoperation, even if the voltage remains within the rated range. Therefore, it
is important to supply a stable voltage to the IC. The recommended power supply control guidelines are that the
commercial frequency (50 to 60 Hz) ripple variation (P-P value) on V
CC
should be less than 10% of the standard
V
CC
value and that the transient rate of change during sudden changes, such as during power supply switching,
should be less than 0.1 V/ms.
7. Notes on Using an External Clock
When using an external clock, drive the X0 pin as illustrated below. When an external clock is used, oscillation
stabilization time is required even for power-on reset and wake-up from stop mode.
Use of External Clock
X0
X1
MB90220
Note: When using an external clock, be sure to input external clock more than 6 machine cycles after
setting the HST pin to “L” to transfer to the hardware standby mode.
相關PDF資料
PDF描述
MB90P224B 8-Bit Proprietary Microcontroller(8位專用微控制器)
MB90P224BPF 16-Bit Edge-Triggered D-type Flip-Flops With 3-State Outputs 48-CFP -55 to 125
MB90W224A 16-bit Proprietary Microcontroller
MB90W224B 16-bit Proprietary Microcontroller
MB90W224BZF 16-bit Proprietary Microcontroller
相關代理商/技術參數
參數描述
MB90223PF 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller
MB90224 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller
MB90224PF 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller
MB90233 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller
MB90233PFV 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*