- 您現在的位置：買賣IC網 > PDF目錄377918 > MB90470B (Fujitsu Limited) 16-Bit Proprietary Microcontroller PDF資料下載
參數資料
| 型號： | MB90470B |
| 廠商： | Fujitsu Limited |
| 英文描述： | 16-Bit Proprietary Microcontroller |
| 中文描述： | 16位微控制器專有 |
| 文件頁數： | 16/118頁 |
| 文件大小： | 555K |
| 代理商： | MB90470B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁
MB90470 Series
16
I
HANDLING DEVICES
(1) Strictly observe maximum rated voltages (prevent latchup)
When CMOS integrated circuit devices are subjected to applied voltages higher than V
CC
at input and output
pins other than medium- and high-withstand voltage pins, or to voltages lower than V
SS
, or when voltages in
excess of rated levels are applied between V
CC
and V
SS
, a phenomenon known as latchup can occur. In a latchup
condition, supply current can increase dramatically and may destroy semiconductor elements. In using
semiconductor devices, always take sufficient care to avoid exceeding maximum ratings.
Also care must be taken when power to analog systems is switched on or off, to ensure that the analog power
supply (AV
CC
, AVRH) and analog input do not exceed the digital power supply (V
CC
) .
(2) Treatment of unused pins
If unused input pins are left open, abnormal operation or latchup may cause permanent damage to the
semiconductor. Any such pins should be pulled up or pulled down through resistance of at least 2 k
.
Also any unused input/output pins should be left open in output status, or if set to input status should be treated
in the same way as input pins.
(3) Precautions for use of external clock signals
Even when an external clock is used, a stabilization period is required following a power-on reset or release
from sub clock mode or stop mode. Also, when an external clock is used 20 MHz should be used as a guideline
for an upper frequency limit.
The following figure shows a sample use of external clock signals.
(4) Power supply pins
When using multiple V
CC
/V
SS
sources, always make sure to design devices with external connections of all power
supply pins to supply or ground elements, in order to prevent latchup, reduce unwanted radiation, and prevent
abnormal strobe signal operation due to rise in ground level, as well as to maintain total rated output current. In
addition, care must be given to connecting the V
CC
and V
SS
pins of this device to a current source with as little
impedance as possible. It is recommended that a bypass capacitor of 1.0
μ
F be connected between V
CC
and
V
SS
as close to the pins as possible.
(5) Crystal oscillator circuits
Abnormal operation of this device can result from noise in the proximity of the X0/X1 and X0A/X1A pins. For
stable operation, it is strongly recommended that the printed circuit artwork provide capacitors placed as close
as possible between the X0/X1, X0A/X1A and crystal oscillator (or ceramic oscillator) as well as ground, and be
wired so as to avoid crossing other wiring wherever possible.
X0
X1
OPEN
相關PDF資料 |
PDF描述 |
|---|---|
| MB90473 | 16-Bit Proprietary Microcontroller |
| MB90473PF | 16-Bit Proprietary Microcontroller |
| MB90473PFV | 16-Bit Proprietary Microcontroller |
| MB90474 | 16-Bit Proprietary Microcontroller |
| MB90474L | 16-Bit Proprietary Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90473 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller |
| MB90473PF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller |
| MB90473PFV | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller |
| MB90474 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller |
| MB90474L | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。