參數資料
型號： MB90473
廠商： Fujitsu Limited
英文描述： 16-Bit Proprietary Microcontroller
中文描述： 16位微控制器專有
文件頁數： 16/118頁
文件大?。?/td> 555K
代理商： MB90473
MB90470 Series
16
I
HANDLING DEVICES
(1) Strictly observe maximum rated voltages (prevent latchup)
When CMOS integrated circuit devices are subjected to applied voltages higher than V
CC
at input and output
pins other than medium- and high-withstand voltage pins, or to voltages lower than V
SS
, or when voltages in
excess of rated levels are applied between V
CC
and V
SS
, a phenomenon known as latchup can occur. In a latchup
condition, supply current can increase dramatically and may destroy semiconductor elements. In using
semiconductor devices, always take sufficient care to avoid exceeding maximum ratings.
Also care must be taken when power to analog systems is switched on or off, to ensure that the analog power
supply (AV
CC
, AVRH) and analog input do not exceed the digital power supply (V
CC
) .
(2) Treatment of unused pins
If unused input pins are left open, abnormal operation or latchup may cause permanent damage to the
semiconductor. Any such pins should be pulled up or pulled down through resistance of at least 2 k
.
Also any unused input/output pins should be left open in output status, or if set to input status should be treated
in the same way as input pins.
(3) Precautions for use of external clock signals
Even when an external clock is used, a stabilization period is required following a power-on reset or release
from sub clock mode or stop mode. Also, when an external clock is used 20 MHz should be used as a guideline
for an upper frequency limit.
The following figure shows a sample use of external clock signals.
(4) Power supply pins
When using multiple V
CC
/V
SS
sources, always make sure to design devices with external connections of all power
supply pins to supply or ground elements, in order to prevent latchup, reduce unwanted radiation, and prevent
abnormal strobe signal operation due to rise in ground level, as well as to maintain total rated output current. In
addition, care must be given to connecting the V
CC
and V
SS
pins of this device to a current source with as little
impedance as possible. It is recommended that a bypass capacitor of 1.0
μ
F be connected between V
CC
and
V
SS
as close to the pins as possible.
(5) Crystal oscillator circuits
Abnormal operation of this device can result from noise in the proximity of the X0/X1 and X0A/X1A pins. For
stable operation, it is strongly recommended that the printed circuit artwork provide capacitors placed as close
as possible between the X0/X1, X0A/X1A and crystal oscillator (or ceramic oscillator) as well as ground, and be
wired so as to avoid crossing other wiring wherever possible.
X0
X1
OPEN
相關PDF資料
PDF描述
MB90473PF 16-Bit Proprietary Microcontroller
MB90473PFV 16-Bit Proprietary Microcontroller
MB90474 16-Bit Proprietary Microcontroller
MB90474L 16-Bit Proprietary Microcontroller
MB90474PF 16-Bit Proprietary Microcontroller
相關代理商/技術參數
參數描述
MB90473PF 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller
MB90473PFV 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller
MB90474 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller
MB90474L 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller
MB90474PF 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*