- 您現在的位置：買賣IC網 > PDF目錄45189 > MB90F347CEPF (FUJITSU COMPONENT LTD) 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | MB90F347CEPF |
| 廠商： | FUJITSU COMPONENT LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | 14 X 20 MM, 3.35 MM HEIGHT, 0.65 MM PITCH, PLASTIC, QFP-100 |
| 文件頁數： | 17/85頁 |
| 文件大?。?/td> | 1173K |
| 代理商： | MB90F347CEPF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
MB90340E Series
24
■ HANDLING DEVICES
1.
Preventing latch-up
CMOS IC chips may suffer latch-up under the following conditions:
A voltage higher than VCC or lower than VSS is applied to an input or output pin.
A voltage higher than the rated voltage is applied between VCC and VSS pins.
The AVCC power supply is applied before the VCC voltage.
Latch-up may increase the power supply current drastically, causing thermal damage to the device.
For the same reason, also be careful not to let the analog power-supply voltage (AVCC, AVRH) exceed the digital
power-supply voltage.
2.
Handling unused pins
Leaving unused input pins open may result in misbehavior or latch-up and possible permanent damage to the
device. Therefore they must be pulled up or pulled down through resistors. In this case those resistors should
be more than 2 k
.
Unused bidirectional pins should be set to the output state and can be left open, or the input state with the above
described connection.
3.
Power supply pins (VCC/VSS)
If there are multiple VCC and VSS pins, that are designed to be set to the same potential are connected the
inside of the device to prevent malfunctions such as latch-up.
To reduce unnecessary radiation, prevent malfunctioning of the strobe signal due to the rise of ground level,
and observe the standard for total output current, be sure to connect the VCC and VSS pins to the power supply
and ground externally. Connect VCC and VSS pins to the device from the current supply source at a low imped-
ance.
As a measure against power supply noise, connect a capacitor of about 0.1
F as a bypass capacitor between
VCC and VSS pins in the vicinity of VCC and VSS pins of the device
4.
Mode Pins (MD0 to MD2)
Connect the mode pins directly to VCC or VSS pins. To prevent the device unintentionally entering test mode due
to noise, lay out the printed circuit board so as to minimize the distance from the mode pins to VCC or VSS pins
and to provide a low-impedance connection.
Vcc
Vss
Vcc
Vss
Vcc
MB90340E
Series
Vcc
Vss
Vcc
Vss
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F349CESPF | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100 |
| MB90341CEPFV | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP100 |
| MB90F347EPFV | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100 |
| MB90349CEPFV | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP100 |
| MB90F346CEPFV | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F349ASPFV-GSE1 | 制造商:FUJITSU 功能描述: |
| MB90F349ASPMC-GSE1 | 制造商:FUJITSU 功能描述: |
| MB90F349CAPFR-GSE1 | 制造商:FUJITSU 功能描述: |
| MB90F349CASPFR-GSE1 | 制造商:FUJITSU 功能描述: |
| MB90F349CASPFV-GSE1 | 制造商:FUJITSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。