- 您現在的位置：買賣IC網 > PDF目錄377923 > MB90F347CES (Fujitsu Limited) 16-bit Proprietary Microcontroller CMOS PDF資料下載
參數資料
| 型號： | MB90F347CES |
| 廠商： | Fujitsu Limited |
| 英文描述： | 16-bit Proprietary Microcontroller CMOS |
| 中文描述： | 16位微控制器專有的CMOS |
| 文件頁數： | 24/85頁 |
| 文件大?。?/td> | 1169K |
| 代理商： | MB90F347CES |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
MB90340E Series
24
■
HANDLING DEVICES
1.
Preventing latch-up
CMOS IC chips may suffer latch
-
up under the following conditions:
A voltage higher than V
CC
or lower than V
SS
is applied to an input or output pin.
A voltage higher than the rated voltage is applied between V
CC
and V
SS
pins.
The AV
CC
power supply is applied before the V
CC
voltage.
Latch-up may increase the power supply current drastically, causing thermal damage to the device.
For the same reason, also be careful not to let the analog power-supply voltage (AV
CC
, AVRH) exceed the digital
power-supply voltage.
Handling unused pins
2.
Leaving unused input pins open may result in misbehavior or latch-up and possible permanent damage to the
device. Therefore they must be pulled up or pulled down through resistors. In this case those resistors should
be more than 2 k
.
Unused bidirectional pins should be set to the output state and can be left open, or the input state with the above
described connection.
Power supply pins (V
CC
/V
SS
)
If there are multiple V
CC
and V
SS
pins, that are designed to be set to the same potential are connected the
inside of the device to prevent malfunctions such as latch-up.
To reduce unnecessary radiation, prevent malfunctioning of the strobe signal due to the rise of ground level,
and observe the standard for total output current, be sure to connect the V
CC
and V
SS
pins to the power supply
and ground externally. Connect V
CC
and V
SS
pins to the device from the current supply source at a low imped-
ance.
As a measure against power supply noise, connect a capacitor of about 0.1
μ
F as a bypass capacitor between
V
CC
and V
SS
pins in the vicinity of V
CC
and V
SS
pins of the device
3.
4.
Mode Pins (MD0 to MD2)
Connect the mode pins directly to V
CC
or V
SS
pins. To prevent the device unintentionally entering test mode due
to noise, lay out the printed circuit board so as to minimize the distance from the mode pins to V
CC
or V
SS
pins
and to provide a low-impedance connection.
Vcc
Vss
Vss
Vcc
Vss
Vcc
MB90340E
Series
Vcc
Vss
Vcc
Vss
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F347CESPF | 16-bit Proprietary Microcontroller CMOS |
| MB90F347CESPFV | 16-bit Proprietary Microcontroller CMOS |
| MB90F347E | 16-bit Proprietary Microcontroller CMOS |
| MB90F347EPF | 16-bit Proprietary Microcontroller CMOS |
| MB90F347EPFV | 16-bit Proprietary Microcontroller CMOS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F349ASPFV-GSE1 | 制造商:FUJITSU 功能描述: |
| MB90F349ASPMC-GSE1 | 制造商:FUJITSU 功能描述: |
| MB90F349CAPFR-GSE1 | 制造商:FUJITSU 功能描述: |
| MB90F349CASPFR-GSE1 | 制造商:FUJITSU 功能描述: |
| MB90F349CASPFV-GSE1 | 制造商:FUJITSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。