參數資料
型號： MB90F349EPF
廠商： FUJITSU LTD
元件分類： 微控制器/微處理器
英文描述： 16-bit Proprietary Microcontroller CMOS
中文描述： 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100
封裝： 20 X 14 MM, 3.35 MM HEIGHT, 0.65 MM PITCH, PLASTIC, QFP-100
文件頁數： 24/85頁
文件大小： 1169K
代理商： MB90F349EPF
MB90340E Series
24
■
HANDLING DEVICES
1.
Preventing latch-up
CMOS IC chips may suffer latch
-
up under the following conditions:
A voltage higher than V
CC
or lower than V
SS
is applied to an input or output pin.
A voltage higher than the rated voltage is applied between V
CC
and V
SS
pins.
The AV
CC
power supply is applied before the V
CC
voltage.
Latch-up may increase the power supply current drastically, causing thermal damage to the device.
For the same reason, also be careful not to let the analog power-supply voltage (AV
CC
, AVRH) exceed the digital
power-supply voltage.
Handling unused pins
2.
Leaving unused input pins open may result in misbehavior or latch-up and possible permanent damage to the
device. Therefore they must be pulled up or pulled down through resistors. In this case those resistors should
be more than 2 k
.
Unused bidirectional pins should be set to the output state and can be left open, or the input state with the above
described connection.
Power supply pins (V
CC
/V
SS
)
If there are multiple V
CC
and V
SS
pins, that are designed to be set to the same potential are connected the
inside of the device to prevent malfunctions such as latch-up.
To reduce unnecessary radiation, prevent malfunctioning of the strobe signal due to the rise of ground level,
and observe the standard for total output current, be sure to connect the V
CC
and V
SS
pins to the power supply
and ground externally. Connect V
CC
and V
SS
pins to the device from the current supply source at a low imped-
ance.
As a measure against power supply noise, connect a capacitor of about 0.1
μ
F as a bypass capacitor between
V
CC
and V
SS
pins in the vicinity of V
CC
and V
SS
pins of the device
3.
4.
Mode Pins (MD0 to MD2)
Connect the mode pins directly to V
CC
or V
SS
pins. To prevent the device unintentionally entering test mode due
to noise, lay out the printed circuit board so as to minimize the distance from the mode pins to V
CC
or V
SS
pins
and to provide a low-impedance connection.
Vcc
Vss
Vss
Vcc
Vss
Vcc
MB90340E
Series
Vcc
Vss
Vcc
Vss
相關PDF資料
PDF描述
MB90F349EPFV 16-bit Proprietary Microcontroller CMOS
MB90F349ESPF 16-bit Proprietary Microcontroller CMOS
MB90F349ESPFV 16-bit Proprietary Microcontroller CMOS
MB90F343CEPF 16-bit Microcontroller
MB90F343CEPFV 16-bit Microcontroller
相關代理商/技術參數
參數描述
MB90F351ESPMC-GSE1 制造商:FUJITSU 功能描述:
MB90F351ESPMCR-GSE1 制造商:FUJITSU 功能描述:
MB90F351PMC-GSE1 制造商:FUJITSU 功能描述:
MB90F351PMC-GS-SPE1 制造商:FUJITSU 功能描述:
MB90F351SPMC-GSE1 制造商:FUJITSU 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*