- 您現在的位置：買賣IC網 > PDF目錄377924 > MB90F351EPMC1 (FUJITSU LTD) 16-bit Proprietary Microcontrollers PDF資料下載
參數資料
| 型號： | MB90F351EPMC1 |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-bit Proprietary Microcontrollers |
| 中文描述： | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP64 |
| 封裝： | 10 X 10 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LQFP-64 |
| 文件頁數： | 26/85頁 |
| 文件大小： | 880K |
| 代理商： | MB90F351EPMC1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
MB90350E Series
26
12. Stabilization of power supply voltage
A sudden change in the power supply voltage may cause the device to malfunction even within the specified
power supply voltage V
CC
operating range. Therefore, the power supply voltage V
CC
should be stabilized.
For reference, the power supply voltage should be controlled so that V
CC
ripple variations (peak-to-peak value)
at commercial frequencies (50 Hz/60 Hz) fall below 10
%
of the standard power supply voltage V
CC
and the
coefficient of fluctuation does not exceed 0.1 V/ms at instantaneous power switching.
13. Initialization
In the device, there are internal registers which are initialized only by a power-on reset. To initialize these
registers, turn on the power again.
14. Port 0 to port 3 output during power-on (External-bus mode)
As shown below, when power is turned on in external-bus mode, there is a possibility that output signal of
Port 0 to Port 3 might be unstable regardless of reset inputs.
15. Setting using CAN function
To use CAN function, please set “1” to DIRECT bit of CAN direct mode register (CDMR).
If DIRECT bit is set to “0” (initial value), wait states will be performed when accessing CAN registers.
Note : Please refer to section “23.12 CAN Direct Mode Register” in Hardware Manual of MB90350E series for detail
of CAN direct mode register.
16. Flash security function
The security byte is located in the area of the Flash memory. If protection code 01
H
is written in the security byte,
the Flash memory is in the protected state by security.
Therefore please do not write 01
H
in this address if you do not use the security function.
Please refer to following table for the address of the security byte.
17. Operation with T
A
=
+
105
°
C or more
If used exceeding T
A
=
+
105
°
C, please contact Fujitsu sales representatives for reliability limitations.
Product name
Flash memory size
Address for security bit
MB90F352E(S)
MB90F352TE(S)
MB90F357E(S)
MB90F357TE(S)
Embedded 1 Mbit Flash memory
FE0001
H
Port 0 to Port
3
Port 0 to Port
3
o
u
tp
u
t
s
might
b
e
u
n
s
t
ab
le.
Port 0 to Port
3
o
u
tp
u
t
s
= Hi-Z
V
CC
1/2 V
CC
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F351ESPMC | 16-bit Proprietary Microcontrollers |
| MB90F351ESPMC1 | 16-bit Proprietary Microcontrollers |
| MB90F351TEPMC | 16-bit Proprietary Microcontrollers |
| MB90F351TEPMC1 | 16-bit Proprietary Microcontrollers |
| MB90F351TESPMC | 16-bit Proprietary Microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F351ESPMC-GSE1 | 制造商:FUJITSU 功能描述: |
| MB90F351ESPMCR-GSE1 | 制造商:FUJITSU 功能描述: |
| MB90F351PMC-GSE1 | 制造商:FUJITSU 功能描述: |
| MB90F351PMC-GS-SPE1 | 制造商:FUJITSU 功能描述: |
| MB90F351SPMC-GSE1 | 制造商:FUJITSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。