參數資料
型號： MB90F395HPMT
元件分類： 微控制器/微處理器
英文描述： 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP120
封裝： PLASTIC, LQFP-120
文件頁數： 8/74頁
文件大?。?/td> 886K
代理商： MB90F395HPMT
MB90390 Series
16
■ HANDLING DEVICES
Special care is required for the following when handling the device :
Preventing latch-up
Stabilization of supply voltage
Treatment of unused pins
Using external clock
Power supply pins (VCC/VSS)
Pull-up/down resistors
Crystal Oscillator Circuit
Turning-on Sequence of Power Supply to A/D Converter and Analog Inputs
Connection of Unused Pins of A/D Converter if A/D Converter is unused.
Notes on Energization
Caution on Operations during PLL Clock Mode
1.
Preventing latch-up
CMOS IC chips may suffer latch-up under the following conditions :
A voltage higher than VCC or lower than VSS is applied to an input or output pin.
A voltage higher than the rated voltage is applied between VCC and VSS.
The AVCC power supply is applied before the VCC voltage.
Latch-up may increase the power supply current drastically, causing thermal damage to the device.
For the same reason, also be careful not to let the analog power-supply voltage (AVCC, AVRH) exceed the digital
power-supply voltage.
2.
Stabilization of supply voltage
A sudden change in the supply voltage may cause the device to malfunction even within the specified VCC supply
voltage operating range. Therefore, the VCC supply voltage should be stabilized.
For reference, the supply voltage should be controlled so that VCC ripple variations (peak-to-peak values) at
commercial frequencies (50/60 Hz) fall below 10% of the standard VCC supply voltage and the coefficient of
fluctuation does not exceed 0.1 V/ms at instantaneous power switching.
3.
Treatment of unused pins
Leaving unused input pins open may result in misbehavior or latch up and possible permanent damage of the
device. Therefore they must be pulled up or pulled down through resistors. In this case those resistors should
be more than 2 k
.
Unused bidirectional pins should be set to the output state and can be left open, or the input state with the above
described connection.
4.
Using external clock
To use external clock, drive the X0 pin and leave X1 pin open.
X0
X1
MB90390 Series
相關PDF資料
PDF描述
MB90428GCPMC 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100
MB90428GAPMC 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100
MB90443GPF 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100
MB90455SPMT 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP48
MB90457PMT 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP48
相關代理商/技術參數
參數描述
MB90F428GAPMC-GSE1 制造商:FUJITSU 功能描述:
MB90F428GCPFR-GSE1 制造商:FUJITSU 功能描述:
MB90F438LSPFR-GE1 制造商:FUJITSU 功能描述:
MB90F438LSPMCR-GE1 制造商:FUJITSU 功能描述:
MB90F439PMCR-GE1 制造商:FUJITSU 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*