- 您現在的位置：買賣IC網 > PDF目錄377930 > MB90M405 (Fujitsu Limited) Octal Edge-Triggered D-type Flip-Flops With Clear 20-CFP -55 to 125 PDF資料下載
參數資料
| 型號： | MB90M405 |
| 廠商： | Fujitsu Limited |
| 英文描述： | Octal Edge-Triggered D-type Flip-Flops With Clear 20-CFP -55 to 125 |
| 中文描述： | F2MC - 16LX系列16位微控制器硬件手冊英文摘要 |
| 文件頁數： | 17/28頁 |
| 文件大?。?/td> | 213K |
| 代理商： | MB90M405 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
GENERAL
1-13
1.8
Notes on Handling Devices
(1)Be careful not to exceed the maximum rated voltage (Prevention of latch up).
For a CMOS IC, latch-up may occur if a voltage higher than Vcc or a voltage lower than Vss is applied to the
I/O pin other than medium-/high-voltage withstand I/O pins, or when a voltage that exceeds the rated
voltage is applied between Vcc and Vss.
Latch up rapidly increases the power current, and the device may be destroyed by heat.
When using the device, take care not to exceed the maximum rating. Also, take care that the analog power
(AVcc) and the analog input do not exceed the digital power (Vcc) when turning the AC/DC power on or off.
(2)Design the device so the supply voltage is as stable as possible.
A sudden change in the power voltage may cause a malfunction even within the operating assurance range
of the VCC power supply voltage. For safety, the VCC ripple (p-p) of the commercial frequency (50/60
MHz) must be 10% or less of the standard VCC value, and the transient fluctuation at instantaneous power
switching must be 0.1 V/ms or less. Also, take countermeasures to power noise, etc.
(3)Notes at power-on
The voltage rise time at power-on must be 50 μs or more (0.2 to 2.7 V).
(4)Setting unused input pins
Leaving unused input pins open may cause a malfunction. Therefore, these pins must be set to the pull-
up or pull-down state.
(5) Handling of power pins for A/D converter
Even when the A/D converter is not used, connect the pins so that the following relationships are
established: AV
CC
= V
CC
, AV
SS
= V
SS
.
(6)Notes on using external clock
Even when an external clock is used, the oscillation stabilization wait time is required at the power-on reset
or the cancellation of the stop mode. In this case, drive the X0 pin only and leave the X1 pin open.
Example of using external clock
X0
X1
MB90M405 Series
OPEN
相關PDF資料 |
PDF描述 |
|---|---|
| MB90M407 | Octal Edge-Triggered D-type Flip-Flops With Clear 20-LCCC -55 to 125 |
| MB90M408 | Octal Edge-Triggered D-type Flip-Flops With Clear 20-CDIP -55 to 125 |
| MB90MV405 | F2MC-16LX FAMILY 16-BIT MICROCONTROLLERS HARDWARE MANUAL ABSTRACTS |
| MB90M407APF | 16-Bit Original Microcontroller |
| MB90M407PF | 16-Bit Original Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90V340A-102CR | 制造商:FUJITSU 功能描述: |
| MB-910 | 制造商:Circuit Test 功能描述:BREADBOARD WIRING KIT - 350 PCS |
| MB9100100 | 制造商:COM/DUO 功能描述:FAN 4-6WKS |
| MB9100-100 | 制造商:COM/DUO 功能描述:FAN 4-6WKS |
| MB91101 | 制造商:Panasonic Industrial Company 功能描述:IC |
發布緊急采購，3分鐘左右您將得到回復。