- 您現在的位置：買賣IC網 > PDF目錄377930 > MB90P214A (Fujitsu Limited) 8-Bit Proprietary Microcontroller(8位專用微控制器) PDF資料下載
參數資料
| 型號： | MB90P214A |
| 廠商： | Fujitsu Limited |
| 英文描述： | 8-Bit Proprietary Microcontroller(8位專用微控制器) |
| 中文描述： | 8位微控制器專利（8位專用微控制器） |
| 文件頁數： | 18/99頁 |
| 文件大?。?/td> | 932K |
| 代理商： | MB90P214A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁
MB90210 Series
18
I
PROGRAMMING FOR MB90P214A/P214B/W214A/W214B
In EPROM mode, the MB90P214A/P214B/W214A/W214B functions equivalent to the MBM27C1000. This
allows the EPROM to be programmed with a general-purpose EPROM programmer by using the dedicated
socket adapter (do not use the electronic signature mode).
1. Program Mode
When shipped from Fujitsu, and after each erasure, all bits (64 K
×
8 bits) in the MB90P214A/P214B/W214A/
W214B are in the “1” state. Data is written to the ROM by selectively programming “0’s” into the desired bit
locations. Bits cannot be set to “1” electrically.
2. Programming Procedure
(1) Set the EPROM programmer to MBM27C1000.
(2) Load program data into the EPROM programmer at 10000
H
to 1FFFF
H
.
Note that ROM addresses FF0000
H
to FFFFFF
H
in the operation mode in the MB90P214A/P214B/W214A/
W214B series assign to 10000
H
to 1FFFF
H
in the EPROM mode (on the EPROM programmer).
(3) Mount the MB90P214A/P214B/W214A/W214B on the adapter socket, then fit the adapter socket onto the
EPROM programmer. When mounting the device and the adapter socket, pay attention to their mounting
orientations.
(4) Start programming the program data to the device.
(5) If programming has not successfully resulted, connect a capacitor of approx. 0.1
μ
F between V
CC
and GND,
between V
PP
and GND.
(6) Since the MB90P214A and MB90W214A have CMOS-level input, programming to them may be impossible
depending on the output level of the general-purpose programmer. In that case, connect a pull-up resistor
to the adapter socket side.
Note: The mask ROM products (MB90214) does not support EPROM mode. Data cannot, therefore, be read by
the EPROM programmer.
FFFFFF
H
10000
H
*
1FFFF
H
*
Operation mode
EPROM mode
(Corresponding addresses on the EPROM mode)
FF0000
H
* : Be sure to set the programming, the start address and the stop address on the EPROM programmer to 10000
H
/1FFFF
H
.
相關PDF資料 |
PDF描述 |
|---|---|
| MB90214 | 8-Bit Proprietary Microcontroller(8位專用微控制器) |
| MB90P214B | 8-Bit Proprietary Microcontroller(8位專用微控制器) |
| MB90V210 | 8-Bit Proprietary Microcontroller(8位專用微控制器) |
| MB90W214A | 8-Bit Proprietary Microcontroller(8位專用微控制器) |
| MB90W214B | 8-Bit Proprietary Microcontroller(8位專用微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90V340A-102CR | 制造商:FUJITSU 功能描述: |
| MB-910 | 制造商:Circuit Test 功能描述:BREADBOARD WIRING KIT - 350 PCS |
| MB9100100 | 制造商:COM/DUO 功能描述:FAN 4-6WKS |
| MB9100-100 | 制造商:COM/DUO 功能描述:FAN 4-6WKS |
| MB91101 | 制造商:Panasonic Industrial Company 功能描述:IC |
發布緊急采購，3分鐘左右您將得到回復。