參數資料
型號： MB91154PFV-G-XXX
元件分類： 微控制器/微處理器
英文描述： 32-BIT, MROM, 33 MHz, RISC MICROCONTROLLER, PQFP144
封裝： PLASTIC, LQFP-144
文件頁數： 25/108頁
文件大?。?/td> 2523K
代理商： MB91154PFV-G-XXX
MB91350A Series
DS07-16503-5E
23
■ HANDLING DEVICES
Preventing Latch-up
Latch-up may occur in a CMOS IC if a voltage greater than VCC or less than VSS is applied to an input or output
pin or if an above-rating voltage is applied between VCC and VSS. A latch-up,if it occurs, significantly increases
the power supply current and may cause thermal destruction of an element. When you use a CMOS IC, don’t
exceed the absolute maximum rating.
Treatment of Unused Pins
Do not leave unused input pins open, as this may cause a malfunction. Handle by using a pull-up or pull-down
resistor.
Power Supply Pins
In products with multiple VCC and VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, you must connect the pins to the external power
supply and ground lines in order to lower the electro-magnetic emission level, to prevent abnormal operation of
strobe signals caused by the rise in the ground level, and to conform to the total output current rating. Moreover,
connect the current supply source to the VCC and VSS pins of this device at the low impedance.
It is also advisable to connect a ceramic bypass capacitor of approximately 0.1
F between VCC and VSS pins
near this device.
Crystal Oscillator Circuit
Noise near the X0, X1, X0A and X1A pins may cause the device to malfunction. Design the printed circuit board
so that X0, X1, X0A, X1A, the crystal oscillator (or ceramic oscillator), and the bypass capacitor to ground are
located close to the device as possible.
It is strongly recommended that the PC board artwork be designed such that the X0, X1, X0A and X1A pins are
surrounded by ground plane, as stable operation can be obtained by using this layout.
Please ask the crystal maker to evaluate the oscillational characteristics of the crystal and this device.
Notes on Using an External Clock
When using an external clock, as a general rule you should simultaneously supply the clock signal to X0 and a
clock signal with the reverse phase to X1. However, the stop mode (oscillator stop mode) must not be used
under this configuration (This is because the X1 pin stops at High level output in STOP mode) .
Using an external clock (normal)
Clock Control Block
Hold the signal for the oscillation stabilization wait time when inputting a Low level to the INIT pin.
X0
X1
Note : STOP mode (oscillation stop mode) cannot be used.
MB91350A series
相關PDF資料
PDF描述
MB91F155APFV-G 32-BIT, FLASH, 33 MHz, RISC MICROCONTROLLER, PQFP144
MB91233LLGA-G-xxx-BNDE1 32-BIT, FLASH, 33.6 MHz, RISC MICROCONTROLLER, PQFP120
MB91233LPMC1-G-XXXE1 32-BIT, FLASH, 33.6 MHz, RISC MICROCONTROLLER, PQFP120
MB91F233APMC1-GE1 32-BIT, FLASH, 33.6 MHz, RISC MICROCONTROLLER, PQFP120
MB91F233LPMC1-GE1 32-BIT, FLASH, 33.6 MHz, RISC MICROCONTROLLER, PQFP120
相關代理商/技術參數
參數描述
MB91155 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontrollers
MB91155PFV-G 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontrollers
MB91155PFV-G-XXX 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontrollers
MB91191 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontroller
MB91191R 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*