參數資料
型號: MB91613PMC
廠商: FUJITSU LTD
元件分類: 微控制器/微處理器
英文描述: 32-BIT, FLASH, 33 MHz, RISC MICROCONTROLLER, PQFP120
封裝: 16 X 16 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LQFP-120
文件頁數: 2/53頁
文件大?。?/td> 2625K
代理商: MB91613PMC
MB89202 Series
10
DS07-12561-2E
■ HANDLING DEVICES
Preventing Latch-up
Latch-up may occur on CMOS ICs if voltage higher than VCC or lower than VSS is applied to input and output pins
other than medium- and high-voltage pins or if higher than the voltage which shows on “1. Absolute Maximum
Ratings” in section “
■ ELECTRICAL CHARACTERISTICS” is applied between VCC and VSS.
When latch-up occurs, power supply current increases rapidly and might thermally damage elements. When
using, take great care not to exceed the absolute maximum ratings.
Treatment of Unused Input Pins
Leaving unused input terminals open may lead to permanent damage due to malfunction and latch-up; pull up
or pull down the terminals through the resistors of 2 k
or more.
Make the unused I/O terminal in a state of output and leave it open or if it is in an input state, handle it with the
same procedure as the input terminals.
Treatment of NC Pins
Be sure to leave (internally connected) NC pins open.
Power Supply Voltage Fluctuations
Although VCC power supply voltage is assured to operate within the rated range, a rapid fluctuation of the voltage
could cause malfunctions, even if it occurs within the rated range. Stabilizing voltage supplied to the IC is therefore
important. As stabilization guidelines, it is recommended to control power so that VCC ripple fluctuations (P-P
value) will be less than 10
% of the standard VCC value at the commercial frequency (50 Hz/60 Hz) and the
transient fluctuation rate will be less than 0.1 V/ms at the time of a momentary fluctuation such as when power
is switched.
Precautions when Using an External Clock
When an external clock is used, oscillation stabilization time is required even for power-on reset (optional) and
wake-up from stop mode.
About the Wild Register Function
No wild register can be debugged on the MB89V201. For the operation check, test the MB89F202/F202Y installed
on a target system.
Program Execution in RAM
When the MB89V201 is used, no program can be executed in RAM.
Note to Noise in the External Reset Pin (RST)
If the reset pulse applied to the external reset pin (RST) does not meet the specifications, it may cause malfunc-
tions. Use caution so that the reset pulse less than the specifications will not be fed to the external reset pin (RST).
External pull-up for the External Reset Pin (RST) of MB89F202
Internal pull-up control for RST pin is not available for MB89F202/F202Y. To ensure proper external reset control
in MB89F202/F202Y, an external pull-up (recommend 100 k
) for RST pin must be required.
Notes on selecting mask option
Please select “With reset output” by the mask option when power-on reset is generated at the power supply ON,
and the device is used without inputting external reset.
相關PDF資料
PDF描述
MPC5567MVR80 FLASH, 80 MHz, MICROCONTROLLER, PBGA416
MPC5567MVZ112 FLASH, 112 MHz, MICROCONTROLLER, PBGA324
MPC5567MVZ132 FLASH, 132 MHz, MICROCONTROLLER, PBGA324
MPC5567MZP112 FLASH, 112 MHz, MICROCONTROLLER, PBGA416
MPC5567MZP132 FLASH, 132 MHz, MICROCONTROLLER, PBGA416
相關代理商/技術參數
參數描述
MB-9-187 功能描述:MOUNTING BUTTON 9/32 TO 11/32 RoHS:是 類別:硬件,緊固件,配件 >> 鉚釘 系列:MB 產品培訓模塊:Rivets and Hardware Engineering Technology Injection Molding and Plastics Plastic Materials 標準包裝:1,000 系列:SR 類型:卡入式 鉚釘直徑:0.197"(5.00mm) 接頭直徑:0.354"(8.99mm) 鉚釘長度:0.260"(6.60mm) 孔直徑:0.203"(5.16mm) 面板厚度:0.098 ~ 0.138"(2.49 ~ 3.51mm) 接頭高度:0.087"(2.21mm) 特點:阻燃 顏色:黑 材質:尼龍 其它名稱:61100367SRVO-5055 BSRVO-5055 B-NDSRVO5055B
MB91F109 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit RISC Microcontroller
MB91F109PF 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit RISC Microcontroller
MB91F109PFR-GE1 制造商:FUJITSU 功能描述:
MB91F109PFV 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit RISC Microcontroller