- 您現在的位置：買賣IC網 > PDF目錄69022 > MB91F264BPFV-GE1 (FUJITSU LTD) 32-BIT, FLASH, 33 MHz, RISC MICROCONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | MB91F264BPFV-GE1 |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, FLASH, 33 MHz, RISC MICROCONTROLLER, PQFP100 |
| 封裝： | LEAD FREE, PLASTIC, LQFP-100 |
| 文件頁數： | 9/60頁 |
| 文件大?。?/td> | 710K |
| 代理商： | MB91F264BPFV-GE1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
MB91260B Series
17
■ HANDLING DEVICES
Preventing Latch-up
Latch-up may occur in a CMOS IC if a voltage greater than VCC or less than VSS is applied to an input or output
pin or if an above-rating voltage is applied between VCC and VSS.
A latch-up, if it occurs, significantly increases the power supply current and may cause thermal destruction of
an element. When you use a CMOS IC, be very careful not to exceed the absolute maximum rating.
Treatment of Unused Pins
Do not leave an unused input pin open, since it may cause a malfunction. Handle by, for example, using a pull-
up or pull-down resistor.
About Power Supply Pins
In products with multiple VCC or VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, you must connect the pins to external power supply
and a ground line to lower the electro-magnetic emission level, to prevent abnormal operation of strobe signals
caused by the rise in the ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with the VCC and VSS pins of this device at the low impedance.
It is also advisable to connect a ceramic bypass capacitor of approximately 0.1
μF between VCC and VSS near
this device.
About Crystal Oscillator Circuit
Noise near the X0, X1, X0A and X1A pins may cause the device to malfunction. Design the printed circuit board
so that X0, X1, X0A and X1A the crystal oscillator (or ceramic oscillator) , and the bypass capacitor to ground
are located as close to the device as possible.
It is strongly recommended to design the PC board artwork with the X0, X1, X0A and X1A pins surrounded by
ground plane because stable operation can be expected with such a layout.
Please ask the crystal maker to evaluate the oscillational characteristics of the crystal and this device.
About Mode Pins (MD0 to MD2)
These pins should be connected directly to VCC or VSS.
To prevent the device erroneously switching to test mode due to noise, design the printed circuit board such that
the distance between the mode pins and VCC or VSS is as short as possible and the connection impedance is low.
Operation at Start-up
Be sure to execute setting initialized reset (INIT) with INIT pin immediately after start-up.
Also, in order to provide the oscillation stabilization wait time for the oscillation circuit immediately after start-up,
hold the “L” level input to the INIT pin for the required stabilization wait time. (For INIT via the INIT pin, the
oscillation stabilization wait time setting is initialized to the minimum value) .
About Oscillation Input at Power On
When turning the power on, maintain clock input until the device is released from the oscillation stabilization
wait state.
相關PDF資料 |
PDF描述 |
|---|---|
| MB91266PFM-G-XXX-E1 | 32-BIT, MROM, 33 MHz, RISC MICROCONTROLLER, PQFP64 |
| MB91266PFM-G-XXX | 32-BIT, MROM, 33 MHz, RISC MICROCONTROLLER, PQFP64 |
| MB91F267PFM-G | 32-BIT, FLASH, 33 MHz, RISC MICROCONTROLLER, PQFP64 |
| MB91267APMC | 32-BIT, MROM, 33 MHz, RISC MICROCONTROLLER, PQFP64 |
| MB91F267NAPMC | 32-BIT, FLASH, 33 MHz, RISC MICROCONTROLLER, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB91F264BPFV-G-E1 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontroller CMOS |
| MB91F267 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontroller |
| MB91F267A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontrollers |
| MB91F267APMC-G | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontrollers |
| MB91F267APMC-GE1 | 功能描述:IC MCU FLASH 128KB FLASH 64LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:FR MB91265A 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
發布緊急采購，3分鐘左右您將得到回復。