- 您現在的位置：買賣IC網 > PDF目錄69022 > MB91F267NAPMC 32-BIT, FLASH, 33 MHz, RISC MICROCONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | MB91F267NAPMC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, FLASH, 33 MHz, RISC MICROCONTROLLER, PQFP64 |
| 封裝： | 12 X 12 MM, 1.70 MM HEIGHT, 0.65 MM PITCH, PLASTIC, LQFP-64 |
| 文件頁數： | 6/54頁 |
| 文件大?。?/td> | 432K |
| 代理商： | MB91F267NAPMC |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
MB91265A Series
14
■ HANDLING DEVICES
Preventing Latch-up
Latch-up may occur in a CMOS IC if a voltage greater than VCC pin or less than VSS pin is applied to an input or
output pin or if an above-rating voltage is applied between VCC and VSS pins.
A latch-up, if it occurs, significantly increases the power supply current and may cause thermal destruction of
an element. When you use a CMOS IC, be very careful not to exceed the absolute maximum rating.
Treatment of Unused Input Pins
Do not leave an unused input pin open, since it may cause a malfunction. Handle by, for example, using a pull-
up or pull-down resistor.
About Power Supply Pins
In products with multiple VCC or VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, you must connect the pins to external power supply
and a ground line to lower the electro-magnetic emission level, to prevent abnormal operation of strobe signals
caused by the rise in the ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with the VCC and VSS pins of this device at the low impedance.
It is also advisable to connect a ceramic bypass capacitor of approximately 0.1
F between VCC and VSS pins
near this device.
About Crystal Oscillator Circuit
Noise near the X0 and X1 pins may cause the device to malfunction. Design the printed circuit board so that X0
and X1 pins the crystal oscillator (or ceramic oscillator) , and the bypass capacitor to ground are located as
close to the device as possible.
It is strongly recommended to design the PC board artwork with the X0 and X1 pins surrounded by ground plane
because stable operation can be expected with such a layout.
Please ask the crystal maker to evaluate the oscillational characteristics of the crystal and this device.
About Mode Pins (MD0 to MD2)
These pins should be connected directly to VCC or VSS pins.
To prevent the device erroneously switching to test mode due to noise, design the printed circuit board such that
the distance between the mode pins and VCC or VSS pins is as short as possible and the connection impedance
is low.
Operation at Start-up
Be sure to execute setting initialized reset (INIT) with INIT pin immediately after start-up.
Also, in order to provide the oscillation stabilization wait time for the oscillation circuit immediately after start-up,
hold the “L” level input to the INIT pin for the required stabilization wait time (For INIT via the INIT pin, the
oscillation stabilization wait time setting is initialized to the minimum value) .
相關PDF資料 |
PDF描述 |
|---|---|
| MB91F361GAPFVS | 32-BIT, FLASH, 64 MHz, RISC MICROCONTROLLER, PQFP208 |
| MB91F361G | 32-BIT, MROM, 64 MHz, MICROCONTROLLER, PQFP208 |
| MB91F368GA | 32-BIT, FLASH, 64 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91F465KAPMT-GSE2 | 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91F467DBPFVS-GSE2 | 32-BIT, FLASH, 96 MHz, RISC MICROCONTROLLER, PQFP208 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB91F267NAPMC-G | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontrollers |
| MB91F267NAPMC-GE1 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontrollers |
| MB91F267NAPMC-GS | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontrollers |
| MB91F267NAPMC-GSE1 | 功能描述:IC MCU FLASH 128KB FLASH 64LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:FR MB91265A 產品培訓模塊:The Ultra-Low Power MSP430 MSP430 Overview MSP430 Design Tools MSP430 Peripherals MSP430x2xx/4xx and Wireless Overview Portable Medical Solutions with MSP430 MSP430 for Utility Metering Solutions MSP430: How to JTAG MSP430, How To Use the Clock System Grace Software Graphical User Interface MCU Overview Driver Library MSP430Ware Overview 標準包裝:1 系列:MSP430x4xx 核心處理器:RISC 芯體尺寸:16-位 速度:8MHz 連通性:SPI，UART/USART 外圍設備:欠壓檢測/復位，LCD，POR，PWM，WDT 輸入/輸出數:48 程序存儲器容量:32KB（32K x 8 + 256B） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:100-LQFP 包裝:Digi-Reel® 其它名稱:296-26232-6 |
| MB91F267NPMC-G | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。