- 您現在的位置：買賣IC網 > PDF目錄67963 > MB95116BPMC 8-BIT, MROM, 16.25 MHz, MICROCONTROLLER, PQFP52 PDF資料下載
參數資料
| 型號： | MB95116BPMC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 16.25 MHz, MICROCONTROLLER, PQFP52 |
| 封裝： | 10 X 10 MM, 1.70 MM HEIGHT, 0.65 MM PITCH, PLASTIC, LQFP-52 |
| 文件頁數： | 7/68頁 |
| 文件大?。?/td> | 2637K |
| 代理商： | MB95116BPMC |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
MB95110B Series
DS07-12615-3E
15
■ PIN CONNECTION
Treatment of Unused Input Pin
Leaving unused input pins unconnected can cause abnormal operation or latch-up, leaving to permanent
damage. Unused input pins should always be pulled up or down through resistance of at least 2 k
Ω.
Any unused input/output pins may be set to output mode and left open, or set to input mode and treated the
same as unused input pins. If there is unused output pin, make it to open.
Treatment of Power Supply Pins on A/D Converter
Connect to be AVCC
= VCC and AVSS = VSS even if the A/D converter is not in use.
Noise riding on the AVCC pin may cause accuracy degradation. So, connect approx. 0.1
μF ceramic capacitor
as a bypass capacitor between AVCC and AVSS pins in the vicinity of this device.
Power Supply Pins
In products with multiple VCC or VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, you must connect the pins to external power supply
and a ground line to lower the electro-magnetic emission level, to prevent abnormal operation of strobe signals
caused by the rise in the ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with the VCC and VSS pins of this device at the low impedance.
It is also advisable to connect a ceramic capacitor of approximately 0.1
μF as a bypass capacitor between VCC
and VSS pins near this device.
Mode Pin (MOD)
Connect the MOD pin directly to VCC or VSS pins.
To prevent the device unintentionally entering test mode due to noise, lay out the printed circuit board so as to
minimize the distance from the MOD pin to VCC or VSS pins and to provide a low-impedance connection.
Analog Power Supply
Always set the same potential to AVCC and VCC . When VCC
> AVCC, the current may flow through the AN00 to
AN07 pins.
相關PDF資料 |
PDF描述 |
|---|---|
| MB95F118BWPV2 | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PBCC48 |
| MB95F118BWPMT | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQFP48 |
| MB95F118HWPMC | 8-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP52 |
| MB95117HPMC | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP52 |
| MB95F118TSPMC | 8-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP52 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB95116BPMT | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers |
| MB95116BPV2 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers |
| MB95117M | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers |
| MB95117MPMC | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Microcontrollers |
| MB95120 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。