- 您現在的位置：買賣IC網 > PDF目錄377934 > MB95F134MBW (Fujitsu Limited) 8-BIT SINGLE CHIP MICROCONTROLLERS PDF資料下載
參數資料
| 型號： | MB95F134MBW |
| 廠商： | Fujitsu Limited |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8-BIT SINGLE CHIP MICROCONTROLLERS |
| 中文描述： | 8位單晶片微控制器 |
| 文件頁數： | 30/64頁 |
| 文件大小： | 795K |
| 代理商： | MB95F134MBW |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
MB95130MB Series
30
*1: The parameter is based on AV
SS
=
V
SS
=
0.0 V.
*2: Apply equal potential to AV
CC
and V
CC
.
*3: V
I
and V
O
should not exceed Vcc + 0.3 V. V
I
must not exceed the rating voltage. However, if the maximum
current to/from an input is limited by some means with external components, the I
CLAMP
rating supersedes
the V
I
rating.
*4: Applicable pins: P10 to P15, PF0, PF1 (Inapplicable pins: PG1, PG2)
Use within recommended operating conditions.
Use at DC voltage (current).
+
B signal is an input signal that exceeds V
CC
voltage. The
+
B signal should always be applied a limiting
resistance placed between the
+
B signal and the microcontroller.
The value of the limiting resistance should be set so that when the
+
B signal is applied the input current
to the microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods.
Note that when the microcontroller drive current is low, such as in the power saving modes, the +B input
potential may pass through the protective diode and increase the potential at the V
CC
pin, and this affects
other devices.
Note that if the
+
B signal is inputted when the microcontroller power supply is off (not fixed at 0 V), the power
supply is provided from the pins, so that incomplete operation may result.
Note that if the
+
B input is applied during power-on, the power supply is provided from the pins and the
resulting power supply voltage may not be sufficient to operate the power-on reset.
Care must be taken not to leave the
+
B input pin open.
Note that analog system input/output pins other than the A/D input pins (LCD drive pins, etc.) cannot accept
+B signal input.
Sample recommended circuits :
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
P-ch
N-ch
Vcc
R
Input/Output Equivalent circuits
+
B input (0 V to 16 V)
Limiting
resistance
Protective diode
相關PDF資料 |
PDF描述 |
|---|---|
| MB95F134NBS | 8-BIT SINGLE CHIP MICROCONTROLLERS |
| MB95F134NBW | 8-BIT SINGLE CHIP MICROCONTROLLERS |
| MB98A51221 | PCMCIA and JEIDA-Compliant 68-pin Two-piece Mask ROM card(PCMCIA和JEIDA兼容68引腳32M掩膜 ROM卡（2個）) |
| MB98A51321 | PCMCIA and JEIDA-Compliant 68-pin Two-piece Mask ROM card(PCMCIA和JEIDA兼容68引腳64M 掩膜 ROM卡（2個）) |
| MB98A51421 | PCMCIA and JEIDA-Compliant 68-pin Two-piece Mask ROM card(PCMCIA和JEIDA兼容68引腳128M 掩膜 ROM卡（2個）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB95F134MBWPF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Microcontrollers |
| MB95F134MBWPFV | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Microcontrollers |
| MB95F134MS | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers |
| MB95F134MW | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers |
| MB95F134NBS | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。