參數資料
型號： MB95F332KP-G-SH-SNE2
廠商： FUJITSU LTD
元件分類： 微控制器/微處理器
英文描述： MICROCONTROLLER, PDIP32
封裝： 1.778 MM PITCH, PLASTIC, DIP-32
文件頁數： 21/68頁
文件大?。?/td> 4600K
代理商： MB95F332KP-G-SH-SNE2
28
DS07–12629–1E
MB95330H Series
(Continued)
*1: The parameter is based on VSS = 0.0 V.
*2: VI and VO must not exceed VCC
+ 0.3 V. VI must not exceed the rated voltage. However, if the maximum
current to/from an input is limited by means of an external component, the ICLAMP rating is used instead of
the VI rating.
*3: Applicable to the following pins: P00 to P07, P10, P11, P13 to P17, P62 to P67, PF0, PF1, PG1 and PG2
Use under recommended operating conditions.
Use with DC voltage (current).
The HV (High Voltage) signal is an input signal exceeding the VCC voltage. Always connect a limiting resistor
between the HV (High Voltage) signal and the microcontroller before applying the HV (High Voltage) signal.
The value of the limiting resistor should be set to a value at which the current to be input to the microcontroller
pin when the HV (High Voltage) signal is input is below the standard value, irrespective of whether the
current is transient current or stationary current.
When the microcontroller drive current is low, such as in low power consumption modes, the HV (High
Voltage) input potential may pass through the protective diode to increase the potential of the VCC pin,
affecting other devices.
If the HV (High Voltage) signal is input when the microcontroller power supply is off (not fixed at 0 V), since
power is supplied from the pins, incomplete operations may be executed.
If the HV (High Voltage) input is input after power-on, since power is supplied from the pins, the voltage
of power supply may not be sufficient to enable a power-on reset.
Do not leave the HV (High Voltage) input pin unconnected.
Example of a recommended circuit
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
HV(High Voltage) input (0 V to 16 V)
Protective diode
VCC
N-ch
P-ch
R
Limiting
resistor
Input/Output equivalent circuit
相關PDF資料
PDF描述
MB95F334KP-G-SH-SNE2 MICROCONTROLLER, PDIP32
MB95F332HWQN-G-SNE1 MICROCONTROLLER, PQCC32
MB95F333HPMC-G-SNE2 MICROCONTROLLER, PQFP32
MB95F332KWQN-G-SNE1 MICROCONTROLLER, PQCC32
MB95F334KPMC-G-SNE2 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQFP32
相關代理商/技術參數
參數描述
MB95F334HPMC-G-SNE2 功能描述:IC MCU 8BIT 20KB FLASH 32LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:F²MC MB95330H 標準包裝:250 系列:LPC11Uxx 核心處理器:ARM? Cortex?-M0 芯體尺寸:32-位 速度:50MHz 連通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，WDT 輸入/輸出數:40 程序存儲器容量:96KB（96K x 8） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-LQFP 包裝:托盤 其它名稱:568-9587
MB95F334KPMC-ES-SNE2 制造商:FUJITSU 功能描述:
MB95F334KPMC-G-SNE2 制造商:FUJITSU 功能描述:MCU 8BIT 8FX 20K FLASH 32LQFP 制造商:FUJITSU 功能描述:MCU, 8BIT, 8FX, 20K FLASH, 32LQFP 制造商:FUJITSU 功能描述:8-bit Microcontroller
MB95F334KWQN-ES-SNE1 制造商:FUJITSU 功能描述:
MB95F352EPF-G-SNE2 功能描述:IC MCU 8BIT 8KB FLASH 24SOP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:F²MC MB95350L 標準包裝:250 系列:LPC11Uxx 核心處理器:ARM? Cortex?-M0 芯體尺寸:32-位 速度:50MHz 連通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，WDT 輸入/輸出數:40 程序存儲器容量:96KB（96K x 8） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-LQFP 包裝:托盤 其它名稱:568-9587
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*