參數資料
型號： MB95F354EWQN-G-SNE1
元件分類： 微控制器/微處理器
英文描述： 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQCC32
封裝： 5 X 5 MM, 0.80 MM HEIGHT, 0.50 MM PITCH, PLASTIC, QFN-32
文件頁數： 17/68頁
文件大?。?/td> 3850K
代理商： MB95F354EWQN-G-SNE1
MB95350L Series
24
DS07–12631–3E
(Continued)
*1: The parameter is based on VSS = 0.0 V.
*2: VI1, VI2 and VO must not exceed VCC
+ 0.3 V. VI1 and VI2 must not exceed the rated voltage. However, if the
maximum current to/from an input is limited by means of an external component, the ICLAMP rating is used
instead of the VI1 and VI2 ratings.
*3: Applicable to the following pins: P00 to P07, P15, P16, P62 to P64, PF0, PF1, PG0 to PG2
Use under recommended operating conditions.
Use with DC voltage (current).
The HV (High Voltage) signal is an input signal exceeding the VCC voltage. Always connect a limiting resistor
between the HV (High Voltage) signal and the microcontroller before applying the HV (High Voltage) signal.
The value of the limiting resistor should be set to a value at which the current to be input to the microcontroller
pin when the HV (High Voltage) signal is input is below the standard value, irrespective of whether the
current is transient current or stationary current.
When the microcontroller drive current is low, such as in low power consumption modes, the HV (High
Voltage) input potential may pass through the protective diode to increase the potential of the VCC pin,
affecting other devices.
If the HV (High Voltage) signal is input when the microcontroller power supply is off (not fixed at 0 V), since
power is supplied from the pins, incomplete operations may be executed.
If the HV (High Voltage) input is input after power-on, since power is supplied from the pins, the voltage
of power supply may not be sufficient to enable a power-on reset.
Do not leave the HV (High Voltage) input pin unconnected.
Example of a recommended circuit
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
HV(High Voltage) input (0 V to 16 V)
Protective diode
VCC
N-ch
P-ch
R
Limiting
resistor
Input/Output equivalent circuit
相關PDF資料
PDF描述
MB95F354LWQN-G-SNERE1 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQCC32
MB95F352LPFT-G-SNE2 MICROCONTROLLER, PDSO24
MB95F352LWQN-G-SNERE1 MICROCONTROLLER, PQCC32
MB95F353EPF-G-SNE2 MICROCONTROLLER, PDSO24
MB95F353LPFT-G-SNE2 MICROCONTROLLER, PDSO24
相關代理商/技術參數
參數描述
MB95F354LPF-G-SNE2 制造商:FUJITSU 功能描述: 制造商:FUJITSU 功能描述:MCU 8BIT 8FX 20K FLASH 24SOP 制造商:FUJITSU 功能描述:MCU, 8BIT, 8FX, 20K FLASH, 24SOP
MB95F374EPMC2-G-SNE2 功能描述:IC MCU 8BIT 20KB FLASH 64LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:8FX MB95370L 標準包裝:60 系列:PSOC® 3 CY8C38xx 核心處理器:8051 芯體尺寸:8-位 速度:67MHz 連通性:EBI/EMI，I²C，LIN，SPI，UART/USART 外圍設備:電容感應，DMA，LCD，POR，PWM，WDT 輸入/輸出數:25 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:2K x 8 RAM 容量:8K x 8 電壓 - 電源 (Vcc/Vdd):1.71 V ~ 5.5 V 數據轉換器:A/D 2x20b，D/A 4x8b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-VFQFN 裸露焊盤 包裝:托盤
MB95F374LPMC1-G-SNE2 制造商:FUJITSU 功能描述:
MB95F376EPMC2-G-SNE2 功能描述:IC MCU 8BIT 36KB FLASH 64LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:8FX MB95370L 標準包裝:250 系列:LPC11Uxx 核心處理器:ARM? Cortex?-M0 芯體尺寸:32-位 速度:50MHz 連通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，WDT 輸入/輸出數:40 程序存儲器容量:96KB（96K x 8） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-LQFP 包裝:托盤 其它名稱:568-9587
MB95F376LPMC1-G-SNE2 制造商:FUJITSU 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*