- 您現在的位置：買賣IC網 > PDF目錄45197 > MB95F394HPMC-G-SNE2 (FUJITSU LTD) 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQFP48 PDF資料下載
參數資料
| 型號： | MB95F394HPMC-G-SNE2 |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQFP48 |
| 封裝： | 7 X 7 MM, 0.50 MM PITCH, 1.70 MM HEIGHT, PLASTIC, LQFP-48 |
| 文件頁數： | 21/60頁 |
| 文件大小： | 3064K |
| 代理商： | MB95F394HPMC-G-SNE2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
MB95390H Series
28
DS07–12632–1E
(Continued)
*1: The parameter is based on VSS = 0.0 V.
*2: VI and VO must not exceed VCC
+ 0.3 V. VI must not exceed the rated voltage. However, if the maximum
current to/from an input is limited by means of an external component, the ICLAMP rating is used instead of
the VI rating.
*3: Applicable to the following pins: P00 to P07, P10, P11, P13 to P17, P40 to P47, P60 to P67, P70, P71,
P74 to P77, PF0, PF1, PG1 and PG2
Use under recommended operating conditions.
Use with DC voltage (current).
The HV (High Voltage) signal is an input signal exceeding the VCC voltage. Always connect a limiting resistor
between the HV (High Voltage) signal and the microcontroller before applying the HV (High Voltage) signal.
The value of the limiting resistor should be set to a value at which the current to be input to the microcontroller
pin when the HV (High Voltage) signal is input is below the standard value, irrespective of whether the
current is transient current or stationary current.
When the microcontroller drive current is low, such as in low power consumption modes, the HV (High
Voltage) input potential may pass through the protective diode to increase the potential of the VCC pin,
affecting other devices.
If the HV (High Voltage) signal is input when the microcontroller power supply is off (not fixed at 0 V), since
power is supplied from the pins, incomplete operations may be executed.
If the HV (High Voltage) input is input after power-on, since power is supplied from the pins, the voltage
of power supply may not be sufficient to enable a power-on reset.
Do not leave the HV (High Voltage) input pin unconnected.
Example of a recommended circuit
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
HV(High Voltage) input (0 V to 16 V)
Protective diode
VCC
N-ch
P-ch
R
Limiting
resistor
Input/Output equivalent circuit
相關PDF資料 |
PDF描述 |
|---|---|
| MB95F396KPMC-G-SNE2 | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQFP48 |
| MB95F418KPMC-G-SNE2 | MICROCONTROLLER, PQFP80 |
| MB95F474HPMC1-G-SNE2 | MICROCONTROLLER, PQFP64 |
| MB95F414HPMC-G-SNE2 | MICROCONTROLLER, PQFP80 |
| MB95F478KPMC1-G-SNE2 | MICROCONTROLLER, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB95F394HWQN-G-SNE1 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Microcontrollers |
| MB95F394HWQN-G-SNERE1 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Microcontrollers |
| MB95F394K | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Microcontrollers |
| MB95F394KPMC1-G-SNE2 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Microcontrollers |
| MB95F394KPMC-G-SNE2 | 功能描述:IC MCU 8BIT 20KB FLASH 48LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:F²MC MB95390H 標準包裝:250 系列:LPC11Uxx 核心處理器:ARM? Cortex?-M0 芯體尺寸:32-位 速度:50MHz 連通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，WDT 輸入/輸出數:40 程序存儲器容量:96KB（96K x 8） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-LQFP 包裝:托盤 其它名稱:568-9587 |
發布緊急采購，3分鐘左右您將得到回復。