參數資料
型號: MB95F564HPF-G-JNE2
元件分類: 微控制器/微處理器
英文描述: 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PDSO20
封裝: 7.50 X 12.70 MM, 1.27 MM PITCH, PLASTIC, SOP-20
文件頁數: 38/84頁
文件大小: 3941K
代理商: MB95F564HPF-G-JNE2
MB95560H/570H/580H Series
DS702-00010-2v0-E
43
(Continued)
*1: The parameter is based on the condition that VSS is 0.0 V.
*2: VI and VO must not exceed VCC
+ 0.3 V. VI must not exceed the rated voltage. However, if the maximum
current to/from an input is limited by means of an external component, the ICLAMP rating is used instead of
the VI rating.
*3: Applicable to the following pins: P00 to P07, P62 to P64, PF0, PF1, PG1, PG2 (P00, and P62 to P64 are
only available on MB95F562H/F562K/F563H/F563K/F564H/F564K. P01, P02, P03, P07, PF0. PF1, PG1
and PG2 are only available on MB95F562H/F562K/F563H/F563K/F564H/F564K/F582H/F582K/F583H/
F583K/F584H/F584K.)
Use under recommended operating conditions.
Use with DC voltage (current).
The HV (High Voltage) signal is an input signal exceeding the VCC voltage. Always connect a limiting resistor
between the HV (High Voltage) signal and the microcontroller before applying the HV (High Voltage) signal.
The value of the limiting resistor should be set to a value at which the current to be input to the microcontroller
pin when the HV (High Voltage) signal is input is below the standard value, irrespective of whether the
current is transient current or stationary current.
When the microcontroller drive current is low, such as in low power consumption modes, the HV (High
Voltage) input potential may pass through the protective diode to increase the potential of the VCC pin,
affecting other devices.
If the HV (High Voltage) signal is input when the microcontroller power supply is off (not fixed at 0 V), since
power is supplied from the pins, incomplete operations may be executed.
If the HV (High Voltage) input is input after power-on, since power is supplied from the pins, the voltage
of power supply may not be sufficient to enable a power-on reset.
Do not leave the HV (High Voltage) input pin unconnected.
Example of a recommended circuit:
*4: P62 and P63 are only available on MB95F562H/F562K/F563H/F563K/F564H/F564K.
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
HV(High Voltage) input (0 V to 16 V)
Protective diode
VCC
N-ch
P-ch
R
Limiting
resistor
Input/Output equivalent circuit
相關PDF資料
PDF描述
MB95F572KPF-G-JNE2 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PDSO8
MB95F582KPFT-G-JNE2 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PDSO16
MB95F582HPF-G-JNE2 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PDSO16
MB95F582HWQN-G-JNE1 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQCC32
MB95F584HPFT-G-JNE2 MICROCONTROLLER, PDSO16
相關代理商/技術參數
參數描述
MB95F564KPF-G-JNE2 功能描述:IC MCU 8BIT 20KB FLASH 20TSSOP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:8FX MB95560H 標準包裝:60 系列:PSOC® 3 CY8C38xx 核心處理器:8051 芯體尺寸:8-位 速度:67MHz 連通性:EBI/EMI,I²C,LIN,SPI,UART/USART 外圍設備:電容感應,DMA,LCD,POR,PWM,WDT 輸入/輸出數:25 程序存儲器容量:64KB(64K x 8) 程序存儲器類型:閃存 EEPROM 大小:2K x 8 RAM 容量:8K x 8 電壓 - 電源 (Vcc/Vdd):1.71 V ~ 5.5 V 數據轉換器:A/D 2x20b,D/A 4x8b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-VFQFN 裸露焊盤 包裝:托盤
MB95F636HP-ES-SH-SNE2 制造商:FUJITSU 功能描述:8-bit MCU
MB95F636HPMC-ES-SNE2 制造商:FUJITSU 功能描述:8-bit FX series microcontroller
MB95F636HWQN-ES-SNE1 制造商:FUJITSU 功能描述:8-bit MCU
MB95F636KP-ES-SH-SNE2 制造商:FUJITSU 功能描述:8-bit FX series microcontroller