- 您現在的位置：買賣IC網 > PDF目錄45199 > MB96F347YWAXXXPQC-GSE2 16-BIT, FLASH, 56 MHz, RISC MICROCONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | MB96F347YWAXXXPQC-GSE2 |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 56 MHz, RISC MICROCONTROLLER, PQFP100 |
| 封裝： | 14 X 20 MM, 3.35 MM HEIGHT, 0.65 MM PITCH, PLASTIC, QFP-100 |
| 文件頁數： | 79/118頁 |
| 文件大小： | 1465K |
| 代理商： | MB96F347YWAXXXPQC-GSE2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁當前第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁
Specication
MB96340
FME/EMDC- 2007-9-12
MB96300_DS_handling.fm
51
PRELIMINARY
s HANDLING DEVICES
Special care is required for the following when handling the device:
Latch-up prevention
Treatment of unused pins
External clock
Precautions for when not using a sub clock signal
Notes on PLL clock mode operation
Power supply pins (VCC/VSS)
Crystal Oscillator Circuit
Turn on Sequence of Power Supply to A/D Converter and Analog Inputs
Connection of Unused Pins of A/D Converter
Notes on Energization
Stabilization of power supply voltage
1.
Preventing latch-up
CMOS IC chips may suffer latch-up under the following conditions:
A voltage higher than VCC or lower than VSS is applied to an input or output pin.
A voltage higher than the rated voltage is applied between VCC and VSS.
The AVCC power supply is applied before the VCC voltage.
Latch-up may increase the power supply current drastically, causing thermal damage to the device.
For the same reason, also be careful not to let the analog power-supply voltage (AVCC, AVRH) exceed the
digital power-supply voltage.
2.
Treatment of unused pins
Unused input pins may be left open when the input is disabled (corresponding bit of Port Input Enable register
PIER = 0).
Leaving unused input pins open when the input is enabled may result in misbehavior and possible permanent
damage of the device. Therefore they must be pulled up or pulled down through resistors. To prevent latch-
up, those resistors should be more than 2 k
.
Unused bidirectional pins can be set either to the output state and be then left open, or to the input state with
either input disabled or external pull-up/pull-down resistor as described above.
3.
External clock usage
To use external clock, drive the X0 pin and leave X1 pin open.
4.
Precautions for when not using a sub clock signal
If you do not connect pins X0A and X1A to an oscillator, use a pull-down resistor on the X0A pin, and leave
the X1A pin open.
5.
Notes on PLL clock mode operation
If the PLL clock mode is selected and no external oscillator is operating or no external clock is supplied, the
microcontroller attempts to work with the freely oscillating PLL. Performance of this operation, however,
cannot be guaranteed.
6.
Power supply pins (VCC/VSS)
Ensure that all VCC-level power supply pins are at the same potential. In addition, ensure the same for all
VSS-level power supply pins. If there are more than one VCC or VSS systems, the device may operate
incorrectly even within the guaranteed operating range.
Connect VCC and VSS to the device from the power supply with lowest possible impedance.
相關PDF資料 |
PDF描述 |
|---|---|
| MB96F348CWBXXXPQC-GSE2 | 16-BIT, FLASH, 56 MHz, RISC MICROCONTROLLER, PQFP100 |
| MB96F356RSBPMC1-GSE2 | 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP64 |
| MB96F356YSBPMC-GSE2 | 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP64 |
| MB96F355ASAPMC1-GSE2 | 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP64 |
| MB96F355AWAPMC-GSE2 | 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB96F348 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB96F348ASA | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB96F348ASAPMC-GE2 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB96F348ASAPMC-GSE2 | 制造商:FUJITSU 功能描述:16BIT MCU 544K FLASH 24K RAM SMD |
| MB96F348ASAPQC-GE2 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。