- 您現在的位置：買賣IC網 > PDF目錄45199 > MB96F353AWAPMC-GSE2 (FUJITSU LTD) 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | MB96F353AWAPMC-GSE2 |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP64 |
| 封裝： | 12 X 12 MM, 1.70 MM HEIGHT, 0.65 MM PITCH, PLASTIC, LQFP-64 |
| 文件頁數： | 52/104頁 |
| 文件大?。?/td> | 2235K |
| 代理商： | MB96F353AWAPMC-GSE2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁當前第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁
MB96350 Series
DS07-13806-2E
51
■ HANDLING DEVICES
Special care is required for the following when handling the device:
Latch-up prevention
Unused pins handling
External clock usage
Unused sub clock signal
Notes on PLL clock mode operation
Power supply pins (VCC/VSS)
Crystal oscillator circuit
Turn on sequence of power supply to A/D converter and analog inputs
Pin handling when not using the A/D converter
Notes on energization
Stabilization of power supply voltage
Serial communication
1.
Latch-up prevention
CMOS IC chips may suffer latch-up under the following conditions:
A voltage higher than VCC or lower than VSS is applied to an input or output pin.
A voltage higher than the rated voltage is applied between VCC pins and VSS pins.
Latch-up may increase the power supply current dramatically, causing thermal damages to the device.
2.
Unused pins handling
Unused input pins can be left open when the input is disabled (corresponding bit of Port Input Enable register
PIER = 0).
Leaving unused input pins open when the input is enabled may result in misbehavior and possible permanent
damage of the device. They must therefore be pulled up or pulled down through resistors. To prevent latch-up,
those resistors should be more than 2 k
Ω.
Unused bidirectional pins can be set either to the output state and be then left open, or to the input state with
either input disabled or external pull-up/pull-down resistor as described above.
3.
External clock usage
The permitted frequency range of an external clock depends on the oscillator type and configuration. See AC
Characteristics for detailed modes and frequency limits. Single and opposite phase external clocks must be
connected as follows:
1. Single phase external clock
When using a single phase external clock, X0 pin must be driven and X1 pin left open.
X0
X1
相關PDF資料 |
PDF描述 |
|---|---|
| MB96F353ASAPMC1-GSE2 | 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP64 |
| MB96F356ASBPMC-GSE2 | 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP64 |
| MB96F355RSAPMC-GSE2 | 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP64 |
| MB96F353ASAPMC-GSE2 | 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP64 |
| MB96F356RWBPMC1-GSE2 | 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB96F353AWBPMC1-GSE2 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB96F353AWBPMC-GSE2 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB96F353RSBPMC1-GSE2 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB96F353RSBPMC-GSE2 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB96F353RWBPMC1-GSE2 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。