參數資料
型號： MB96F379RSAPMC1-GSE2
元件分類： 微控制器/微處理器
英文描述： 16-BIT, FLASH, 80 MHz, MICROCONTROLLER, PQFP144
封裝： 16 X 16 MM, 1.70 MM HEIGHT, 0.40 MM PITCH, PLASTIC, LQFP-144
文件頁數： 71/112頁
文件大?。?/td> 3105K
代理商： MB96F379RSAPMC1-GSE2
PRELIMINARY
MB96370 Series
FME-MB96370 rev 4
61
■ HANDLING DEVICES
Special care is required for the following when handling the device:
Latch-up prevention
Unused pins handling
External clock usage
Unused sub clock signal
Notes on PLL clock mode operation
Power supply pins (VCC/VSS)
Crystal oscillator circuit
Turn on sequence of power supply to A/D converter and analog inputs
Pin handling when not using the A/D converter
Notes on energization
Stabilization of power supply voltage
SMC power supply pins
Serial communication
1.
Latch-up prevention
CMOS IC chips may suffer latch-up under the following conditions:
A voltage higher than VCC or lower than VSS is applied to an input or output pin.
A voltage higher than the rated voltage is applied between VCC pins and VSS pins.
The AVCC power supply is applied before the VCC voltage.
Latch-up may increase the power supply current dramatically, causing thermal damages to the device.
For the same reason, extra care is required to not let the analog power-supply voltage (AVCC, AVRH) exceed
the digital power-supply voltage.
2.
Unused pins handling
Unused input pins can be left open when the input is disabled (corresponding bit of Port Input Enable register
PIER = 0).
Leaving unused input pins open when the input is enabled may result in misbehavior and possible permanent
damage of the device. They must therefore be pulled up or pulled down through resistors. To prevent latch-up,
those resistors should be more than 2 k
.
Unused bidirectional pins can be set either to the output state and be then left open, or to the input state with
either input disabled or external pull-up/pull-down resistor as described above.
3.
External clock usage
The permitted frequency range of an external clock depends on the oscillator type and conguration. See AC
Characteristics for detailed modes and frequency limits. Single and opposite phase external clocks must be
connected as follows:
1. Single phase external clock
When using a single phase external clock, X0 pin must be driven and X1 pin left open.
X0
X1
相關PDF資料
PDF描述
MB96F378TSAPMC-GSE2 16-BIT, FLASH, 80 MHz, MICROCONTROLLER, PQFP144
MB96F379RWAPMC-GSE2 16-BIT, FLASH, 80 MHz, MICROCONTROLLER, PQFP144
MB96F379YSAPMC1-GSE2 16-BIT, FLASH, 80 MHz, MICROCONTROLLER, PQFP144
MB96F389RWAPMC-GSE2 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP120
MB96385YSBPMC-GSE2 16-BIT, MROM, 56 MHz, MICROCONTROLLER, PQFP120
相關代理商/技術參數
參數描述
MB96F385 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller
MB96F385RSBPMC-GSE2 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller
MB96F385RWBPMC-GSE2 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller
MB96F385YSBPMC-GSE2 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller
MB96F385YWBPMC-GSE2 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*