參數資料
型號： MB98C81333
廠商： Fujitsu Limited
英文描述： 8M-Byte5 V-Only Flash Miniature Card(單5V 電源16M位 微型閃存卡)
中文描述： 800萬Byte5 V型微型只有閃存卡（單5V的電源1,600位微型閃存卡）
文件頁數： 10/48頁
文件大?。?/td> 483K
代理商： MB98C81333
10
MB98C81013/81123/81233/81333-10
I
FUNCTION DESCRIPTIONS
1. Read Mode
The data in the common can be read with “OE# = VIL” and “WE# = VIH”. The address is selected with A0-A21.
And CEL# and CEH# select output mode.
2. Standby Mode
– CEL# and CEH# at “VIH” place the card in Standby mode. D0-D15 are placed in a high-Z state independent
of the status “OE#” and “WE#”.
3. Output Disable Mode
– The outputs are disabled with OE# and WE# at “VIH”. D0-D15 are placed in high-Z state.
4. Write Mode
– The card is in Write mode with “OE# = VIH” and “WE# and CE# = VIL”.
– Commands can be written at the Write mode.
– Two types of the Write mode, “WE# control” and “CE# control” are available.
5. Command Definitions
– User can select the card operation by writing the specific address and data sequences into the command
register. If incollect address and data are written or improper sequence is done, the card is reseted to read
mode. See “COMMAND DEFINISION TABLE”.
6. Automated Program Capability
– Programming operation can switch the data from “1” to “0”.
– The data is programmed on a byte-by-byte or word-by-word basis.
– The card will automatically provide adequate internally generated programming pulses and verify the pro-
grammed cell margin by writing four bus cycle operation. The card returns to Common Memory Read mode
automatically after the programming is completed.
– Addresses are latched at falling edge of WE# or CE# and data is latched at rising edge of WE# or CE#. The
fourth rising edge of WE# or CE# on the command write cycle begins programming operation.
– We can check whether a byte (word) programming operation is completed successfully by sequence flug with
BUSY# (except MB98C81013), Data# Polling or Toggle Bit function. See “WRITE OPERATION STATUS”.
– Any commands written to the chip during programming operation will be ignored.
7. Automated Chip Erase Capability
– We can execute chip erase operation by 6 bus cycle operation. Chip erase does not require the user to program
the chip prior to erase. Upon executing the Erase command sequence the chip automatically will program
and verify the entire memory for an all zero data pattern prior to electrical erase. The system is not required
to provide any controls or timing during these operations.
– The card returns to Common Memory Read mode automatically after the chip erasing is completed.
– Whether or not chip erase operation is completed successfully can be checked by sequence flug with BUSY#
(except MB98C81013), Data# Polling or Toggle Bit function. See “WRITE OPERATION STATUS”.
– Any commands written to the chip during programming operation will be ignored.
相關PDF資料
PDF描述
MB98C81233 4M-Byte5 V-Only Flash Miniature Card(單5V 電源 8M位 微型閃存卡)
MB98C81123 2M-Byte5 V-Only Flash Miniature Card(單5V電源 4M位 微型閃存卡)
MB98D81223 3V Only 4M Bits Flash Miniature Cards(單3V 4M 微型閃存卡)
MB98D81123 3V Only 2M Bits Flash Miniature Cards(單3V 2M 微型閃存卡)
MBF110 Solid-State Fingerprint Sensor
相關代理商/技術參數
參數描述
MB990SP-B 制造商:Icy Dock 功能描述:Dual 2.5" SATA/IDE Hard Drive to Single 3.5" Drive Bay Adapter 制造商:ICY DOCK 功能描述:DUAL 2.5 TO 3.5 DRIVE BRACKET SATA/IDE HDD AND SSD
MB991IK-B 制造商:Icy Dock 功能描述:2.5" SATA/SAS Drive Rack for 3.5" Drive Bay
MB992SK-B 制造商:Icy Dock 功能描述:2 X 2.5 INCH SATA 3.5 IN DRIVE
MB994IPO-3SB 制造商:Icy Dock 功能描述:2 X 2.5 INCH SAS~SATA + 1 SLIM
MB994SP-4S 制造商:Icy Dock 功能描述:5.25" Drive Bay Holds Four 2.5" Hard Drives SAS/SATA 制造商:ICY DOCK 功能描述:4X 2.5 HDD 5.25 IN DRIVE BAY SAS/SATA HOT SWAP RAID CAGE
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*