- 您現在的位置：買賣IC網 > PDF目錄377937 > MBM29DL162BE70PFTN (Fujitsu Limited) 16M (2M x 8/1M x 16) BIT Dual Operation PDF資料下載
參數資料
| 型號： | MBM29DL162BE70PFTN |
| 廠商： | Fujitsu Limited |
| 英文描述： | 16M (2M x 8/1M x 16) BIT Dual Operation |
| 中文描述： | 16米（2米x 8/1M × 16）位雙操作 |
| 文件頁數： | 27/75頁 |
| 文件大小： | 1089K |
| 代理商： | MBM29DL162BE70PFTN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁
MBM29DL16XTE/BE
-70/90/12
27
RESET
Hardware Reset
The MBM29DL16XTE/BE devices may be reset by driving the RESET pin to V
IL
. The RESET pin has a pulse
requirement and has to be kept low (V
IL
) for at least “t
RP
” in order to properly reset the internal state machine.
Any operation in the process of being executed will be terminated and the internal state machine will be reset
to the read mode “t
READY
” after the RESET pin is driven low. Furthermore, once the RESET pin goes high, the
devices require an additional “t
RH
” before it will allow read access. When the RESET pin is low, the devices will
be in the standby mode for the duration of the pulse and all the data output pins will be tri-stated. If a hardware
reset occurs during a program or erase operation, the data at that particular location will be corrupted. Please
note that the RY/BY output signal should be ignored during the RESET pulse. See Figure 14 for the timing
diagram. Refer to Temporary Sector Group Unprotection for additional functionality.
Boot Block Sector Protection
The Write Protect function provides a hardware method of protecting certain boot sectors without using V
ID
. This
function is one of two provided by the WP/ACC pin.
If the system asserts V
IL
on the WP/ACC pin, the device disables program and erase functions in the two
“outermost” 8K byte boot sectors independently of whether those sectors were protected or unprotected using
the method described in “Sector Protection/Unprotection”. The two outermost 8K byte boot sectors are the two
sectors containing the lowest addresses in a bottom-boot-configured device, or the two sectors containing the
highest addresses in a top-boot-congfigured device.
(MBM29DL16XTE: SA37 and SA38, MBM29DL16XBE: SA0 and SA1)
If the system asserts V
IH
on the WP/ACC pin, the device reverts to whether the two outermost 8K byte boot
sectors were last set to be protected or unprotected. That is, sector protection or unprotection for these two
sectors depends on whether they were last protected or unprotected using the method described in “Sector
protection/unprotection”.
Accelerated Program Operation
MBM29DL16XTE/BE offers accelerated program operation which enables the programming in high speed. If
the system asserts V
ACC
to the WP/ACC pin, the device automatically enters the acceleration mode and the time
required for program operation will reduce to about 60%. This function is primarily intended to allow high speed
program, so caution is needed as the sector group will temporarily be unprotected.
The system would use a fact program command sequence when programming during acceleration mode.
Set command to fast mode and reset command from fast mode are not necessary. When the device enters the
acceleration mode, the device automatically set to fast mode. Therefore, the pressent sequence could be
used for programming and detection of completion during acceleration mode.
Removing V
ACC
from the WP/ACC pin returns the device to normal operation. Do not remove V
ACC
from WP/
ACC pin while programming. See Figure 21.
相關PDF資料 |
PDF描述 |
|---|---|
| MBM29DL164BE70PFTR | 16M (2M x 8/1M x 16) BIT Dual Operation |
| MBM29DL162BE70PFTR | 16M (2M x 8/1M x 16) BIT Dual Operation |
| MBM29DL164BE70TN | 16M (2M X 8/1M X 16) BIT Dual Operation |
| MBM29DL162BE70TN | 16M (2M X 8/1M X 16) BIT Dual Operation |
| MBM29DL164BE70TR | 16M (2M X 8/1M X 16) BIT Dual Operation |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MBM29DL162BE70PFTR | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M x 8/1M x 16) BIT Dual Operation |
| MBM29DL162BE70TN | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8/1M X 16) BIT Dual Operation |
| MBM29DL162BE-70TN | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation |
| MBM29DL162BE70TR | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8/1M X 16) BIT Dual Operation |
| MBM29DL162BE-70TR | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation |
發布緊急采購，3分鐘左右您將得到回復。