參數資料
型號： MBM29DL321BE80TN
廠商： FUJITSU LTD
元件分類： DRAM
英文描述： ECONOMY CROSSOVER MEDIA CONVERTR ECO UTP TO FIBER
中文描述： 2M X 16 FLASH 3V PROM, 80 ns, PDSO48
封裝： PLASTIC, TSOP1-48
文件頁數： 40/80頁
文件大?。?/td> 1588K
代理商： MBM29DL321BE80TN
MBM29DL32XTE/BE
-80/90/12
40
Multiple sectors may be erased concurrently by writing the six bus cycle operations on Table 5. This sequence
is followed with writes of the Sector Erase command to addresses in other sectors desired to be concurrently
erased. The time between writes must be less than “t
TOW
” otherwise that command will not be accepted and
erasure will start. It is recommended that processor interrupts be disabled during this time to guarantee this
condition. The interrupts can be re-enabled after the last Sector Erase command is written. A time-out of “t
TOW
”
from the rising edge of last CE or WE whichever happens first will initiate the execution of the Sector Erase
command(s). If another falling edge of CE or WE, whichever happens first occurs within the “t
TOW
” time-out
window the timer is reset. (Monitor DQ
3
to determine if the sector erase timer window is still open, see section
DQ
3
, Sector Erase Timer.) Any command other than Sector Erase or Erase Suspend during this time-out period
will reset the devices to the read mode, ignoring the previous command string. Resetting the devices once
execution has begun will corrupt the data in the sector. In that case, restart the erase on those sectors and allow
them to complete. (Refer to the Write Operation Status section for Sector Erase Timer operation.) Loading the
sector erase buffer may be done in any sequence and with any number of sectors (0 to 38).
Sector erase does not require the user to program the devices prior to erase. The devices automatically program
all memory locations in the sector(s) to be erased prior to electrical erase (Preprogram function). When erasing
a sector or sectors the remaining unselected sectors are not affected. The system is not required to provide any
controls or timings during these operations.
The system can determine the status of the erase operation by using DQ
7
(Data Polling), DQ
6
(Toggle Bit), or
RY/BY.
The sector erase begins after the “t
TOW
” time out from the rising edge of CE or WE whichever happens first for
the last sector erase command pulse and terminates when the data on DQ
7
is “1” (See Write Operation Status
section.) at which time the devices return to the read mode. Data polling and Toggle Bit must be performed at
an address within any of the sectors being erased.
Multiple Sector Erase Time; [Sector Erase Time + Sector Program Time (Preprogramming)]
×
Number of Sector
Erase
In case of multiple sector erase across bank boundaries, a read from bank (read-while-erase) can not perform.
Figure 23 illustrates the Embedded Erase
TM
Algorithm using typical command strings and bus operations.
Erase Suspend/Resume
The Erase Suspend command allows the user to interrupt a Sector Erase operation and then perform data reads
from or programs to a sector not being erased. This command is applicable ONLY during the Sector Erase
operation which includes the time-out period for sector erase. The Erase Suspend command will be ignored if
written during the Chip Erase operation or Embedded Program Algorithm. Writing the Erase Suspend command
(B0h) during the Sector Erase time-out results in immediate termination of the time-out period and suspension
of the erase operation.
Writing the Erase Resume command (30h) resumes the erase operation. The bank addresses of sector being
erasing or suspending should be set when writing the Erase Suspend or Erase Resume command.
When the Erase Suspend command is written during the Sector Erase operation, the device will take a maximum
of “t
SPD
” to suspend the erase operation. When the devices have entered the erase-suspended mode, the
RY/BY output pin will be at Hi-Z and the DQ
7
bit will be at logic “1”, and DQ
6
will stop toggling. The user must
use the address of the erasing sector for reading DQ
6
and DQ
7
to determine if the erase operation has been
suspended. Further writes of the Erase Suspend command are ignored.
When the erase operation has been suspended, the devices default to the erase-suspend-read mode. Reading
data in this mode is the same as reading from the standard read mode except that the data must be read from
sectors that have not been erase-suspended. Successively reading from the erase-suspended sector while the
device is in the erase-suspend-read mode will cause DQ
2
to toggle. (See the section on DQ
2
.)
After entering the erase-suspend-read mode, the user can program the device by writing the appropriate com-
mand sequence for Program. This program mode is known as the erase-suspend-program mode. Again, pro-
gramming in this mode is the same as programming in the regular Program mode except that the data must be
相關PDF資料
PDF描述
MBM29DL321BE80TR UTP/AUI MINI CONVERTER
MBM29DL321BE90PBT 10BASE-T TO AUI
MBM29DL321BE90TN MINI BNC TRANSCEIVER
MBM29DL321TD-12 32M (4M X 8/2M X 16) BIT Dual Operation
MBM29DL321TD-80 32M (4M X 8/2M X 16) BIT Dual Operation
相關代理商/技術參數
參數描述
MBM29DL321BE-80TN 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32M (4M x 8/2M x 16) BIT Dual Operation
MBM29DL321BE80TR 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32M (4M x 8/2M x 16) BIT Dual Operation
MBM29DL321BE-80TR 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32M (4M x 8/2M x 16) BIT Dual Operation
MBM29DL321BE90PBT 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32M (4M x 8/2M x 16) BIT Dual Operation
MBM29DL321BE-90PBT 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32M (4M x 8/2M x 16) BIT Dual Operation
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*