- 您現在的位置：買賣IC網 > PDF目錄377937 > MBM29DL321BE (Fujitsu Limited) 32M (4M x 8/2M x 16) BIT Dual Operation PDF資料下載
參數資料
| 型號： | MBM29DL321BE |
| 廠商： | Fujitsu Limited |
| 英文描述： | 32M (4M x 8/2M x 16) BIT Dual Operation |
| 中文描述： | 32M的（4米× 8/2M × 16）位雙操作 |
| 文件頁數： | 56/84頁 |
| 文件大小： | 1629K |
| 代理商： | MBM29DL321BE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁當前第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
MBM29DL32XTD/BD
-80/90/12
56
Write
Device erasure and programming are accomplished via the command register. The contents of the register serve
as inputs to the internal state machine. The state machine outputs dictate the function of the device.
The command register itself does not occupy any addressable memory location. The register is a latch used to
store the commands, along with the address and data information needed to execute the command. The
command register is written by bringing WE to V
IL
, while CE is at V
IL
and OE is at V
IH
. Addresses are latched on
the falling edge of WE or CE, whichever happens later; while data is latched on the rising edge of WE or CE,
whichever happens first. Standard microprocessor write timings are used.
Refer to AC Write Characteristics and the Erase/Programming Waveforms for specific timing parameters.
Sector Group Protection
The MBM29DL32XTD/BD feature hardware sector group protection. This feature will disable both program and
erase operations in any combination of twenty five sector groups of memory. (See Tables 9.1 and 9.2). The
sector group protection feature is enabled using programming equipment at the user’s site. The device is shipped
with all sector groups unprotected.
To activate this mode, the programming equipment must force V
ID
on address pin A
9
and control pin OE, (suggest
V
ID
= 11.5 V), CE = V
IL
and A
0
= A
6
= V
IL
, A
1
= V
IH
. The sector group addresses (A
20
, A
19
, A
18
, A
17
, A
16
, A
15
, A
14
,
A
13
, and A
12
) should be set to the sector to be protected. Tables 5.1 to 8.2 define the sector address for each of
the seventy one (71) individual sectors, and tables 9.1 and 9.2 define the sector group address for each of the
twenty five (25) individual group sectors. Programming of the protection circuitry begins on the falling edge of
the WE pulse and is terminated with the rising edge of the same. Sector group addresses must be held constant
during the WE pulse. See Figures 18 and 26 for sector group protection waveforms and algorithm.
To verify programming of the protection circuitry, the programming equipment must force V
ID
on address pin A
9
with CE and OE at V
IL
and WE at V
IH
. Scanning the sector group addresses (A
20
, A
19
, A
18
, A
17
, A
16
, A
15
, A
14
, A
13
,
and A
12
) while (A
6
, A
1
, A
0
) = (0, 1, 0) will produce a logical “1” code at device output DQ
0
for a protected sector.
Otherwise the device will produce “0” for unprotected sector. In this mode, the lower order addresses, except
for A
0
, A
1
, and A
6
are DON’T CARES. Address locations with A
1
= V
IL
are reserved for Autoselect manufacturer
and device codes. A
-1
requires to apply to V
IL
on byte mode.
It is also possible to determine if a sector group is protected in the system by writing an Autoselect command.
Performing a read operation at the address location XX02H, where the higher order addresses (A
20
, A
19
, A
18
,
A
17
, A
16
, A
15
, A
14
, A
13
, and A
12
) are the desired sector group address will produce a logical “1” at DQ
0
for a protected
sector group. See Tables 11.1 to 11.8 for Autoselect codes.
Temporary Sector Group Unprotection
This feature allows temporary unprotection of previously protected sector groups of the MBM29DL32XTD/BD
devices in order to change data. The Sector Group Unprotection mode is activated by setting the RESET pin to
high voltage (V
ID
). During this mode, formerly protected sector groups can be programmed or erased by selecting
the sector group addresses. Once the V
ID
is taken away from the RESET pin, all the previously protected sector
groups will be protected again. Refer to Figures 19 and 27.
相關PDF資料 |
PDF描述 |
|---|---|
| MBM29DL322TE12PBT | 32M (4M x 8/2M x 16) BIT Dual Operation |
| MBM29DL321BD-12 | 32M (4M X 8/2M X 16) BIT Dual Operation |
| MBM29DL321BD-80 | 32M (4M X 8/2M X 16) BIT Dual Operation |
| MBM29DL321BD-80PBT | OFFICE 802.3 TRANS CBL 1M |
| MBM29DL321BE-12PBT | MICRO SINGLE MODE FIBER TRANCEIVER, ST |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MBM29DL321BE12PBT | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32M (4M x 8/2M x 16) BIT Dual Operation |
| MBM29DL321BE-12PBT | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32M (4M x 8/2M x 16) BIT Dual Operation |
| MBM29DL321BE12TN | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32M (4M x 8/2M x 16) BIT Dual Operation |
| MBM29DL321BE-12TN | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32M (4M x 8/2M x 16) BIT Dual Operation |
| MBM29DL321BE12TR | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32M (4M x 8/2M x 16) BIT Dual Operation |
發布緊急采購，3分鐘左右您將得到回復。