參數資料
型號： MBM29DL400BC-12
廠商： Fujitsu Limited
英文描述： LED Lamp; LED Color:Blue; Luminous Intensity:37mcd; Viewing Angle:120 ; Forward Current:20mA; Forward Voltage:3.5V; Operating Temperature Range:-40 C to +85 C; Leaded Process Compatible:Yes; Peak Reflow Compatible (260 C):Yes RoHS Compliant: Yes
中文描述： 4分（為512k × 8/256K × 16）位
文件頁數： 13/56頁
文件大?。?/td> 551K
代理商： MBM29DL400BC-12
13
MBM29DL400TC
-55/-70/-90/-12
/MBM29DL400BC
-55/-70/-90/-12
Write
Device erasure and programming are accomplished via the command register. The contents of the register serve
as inputs to the internal state machine. The state machine outputs dictate the function of the device.
The command register itself does not occupy any addressable memory location. The register is a latch used to
store the commands, along with the address and data information needed to execute the command. The
command register is written by bringing WE to V
IL
, while CE is at V
IL
and OE is at V
IH
. Addresses are latched on
the falling edge of WE or CE, whichever happens later; while data is latched on the rising edge of WE or CE,
whichever happens first. Standard microprocessor write timings are used.
Refer to AC Write Characteristics and the Erase/Programming Waveforms for specific timing parameters.
Sector Protection
The MBM29DL400TC/BC feature hardware sector protection. This feature will disable both program and erase
operations in any number of sectors (0 through 13). The sector protection feature is enabled using programming
equipment at the user’s site. The devices are shipped with all sectors unprotected. Alternatively, Fujitsu may
program and protect sectors in the factory prior to shiping the device.
To activate this mode, the programming equipment must force V
ID
on address pin A
9
and control pin OE, (suggest
V
ID
= 11.5 V), CE = V
IL
, and A
0
= A
6
= V
IL
, A
1
= V
IH
. The sector addresses (A
17
, A
16
, A
15
, A
14
, A
13
, and A
12
) should
be set to the sector to be protected. Tables 6 and 7 define the sector address for each of the forteen (14)
individual sectors. Programming of the protection circuitry begins on the falling edge of the WE pulse and is
terminated with the rising edge of the same. Sector addresses must be held constant during the WE pulse. See
Figures 16 and 25 for sector protection waveforms and algorithm.
To verify programming of the protection circuitry, the programming equipment must force V
ID
on address pin A
9
with CE and OE at V
IL
and WE at V
IH
. Scanning the sector addresses (A
17
, A
16
, A
15
, A
14
, A
13
, and A
12
) while (A
6
,
A
1
, A
0
) = (0, 1, 0) will produce a logical “1” code at device output DQ
0
for a protected sector. Otherwise the
devices will read 00H for unprotected sector. In this mode, the lower order addresses, except for A
0
, A
1
, and A
6
are DON’T CARES. Address locations with A
1
= V
IL
are reserved for Autoselect manufacturer and device codes.
A
-1
requires to apply to V
IL
on byte mode.
It is also possible to determine if a sector is protected in the system by writing an Autoselect command. Performing
a read operation at the address location XX02H, where the higher order addresses (A
17
, A
16
, A
15
, A
14
, A
13
, and
A
12
) are the desired sector address will produce a logical “1” at DQ
0
for a protected sector. See Tables 5.1 and
5.2 for Autoselect codes.
Temporary Sector Unprotection
This feature allows temporary unprotection of previously protected sectors of the MBM29DL400TC/BC devices
in order to change data. The Sector Unprotection mode is activated by setting the RESET pin to high voltage
(12 V). During this mode, formerly protected sectors can be programmed or erased by selecting the sector
addresses. Once the 12 V is taken away from the RESET pin, all the previously protected sectors will be protected
again. See Figures 17 and 26.
相關PDF資料
PDF描述
MBM29DL640E 64 M (8 M X 8/4 M X 16) BIT Dual Operation
MBM29DL640E12 64 M (8 M X 8/4 M X 16) BIT Dual Operation
MBM29DL640E12PBT 64 M (8 M X 8/4 M X 16) BIT Dual Operation
MBM29DL640E12TN 64 M (8 M X 8/4 M X 16) BIT Dual Operation
MBM29DL640E12TR 64 M (8 M X 8/4 M X 16) BIT Dual Operation
相關代理商/技術參數
參數描述
MBM29DL400BC-55 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:4M (512K X 8/256K X 16) BIT
MBM29DL400BC-70 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:4M (512K X 8/256K X 16) BIT
MBM29DL400BC-90 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:4M (512K X 8/256K X 16) BIT
MBM29DL400TC 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:4M (512K X 8/256K X 16) BIT
MBM29DL400TC-12 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:4M (512K X 8/256K X 16) BIT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*