- 您現在的位置：買賣IC網 > PDF目錄377943 > MBM29F040C (Fujitsu Limited) 4M (512K X 8) BIT PDF資料下載
參數資料
| 型號： | MBM29F040C |
| 廠商： | Fujitsu Limited |
| 英文描述： | 4M (512K X 8) BIT |
| 中文描述： | 4分（為512k × 8）位 |
| 文件頁數： | 10/40頁 |
| 文件大?。?/td> | 424K |
| 代理商： | MBM29F040C |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
10
MBM29F040C
-55/-70/-90
* :Outputs 01H at protected sector addresses and 00H at unprotected sector addresses.
Write
Device erasure and programming are accomplished via the command register. The contents of the register serve
as inputs to the internal state machine. The state machine outputs dictate the function of the device.
The command register itself does not occupy any addressable memory location. The register is a latch used to
store the commands, along with the address and data information needed to execute the command. The
command register is written by bringing WE to V
IL
, while CE is at V
IL
and OE is at V
IH
. Addresses are latched on
the falling edge of WE or CE, whichever happens later; while data is latched on the rising edge of WE or CE,
whichever happens first. Standard microprocessor write timings are used.
Refer to AC Write Characteristics and the Erase/Programming Waveforms for specific timing parameters.
Sector Protection
The MBM29F040C features hardware sector protection. This feature will disable both program and erase
operations in any number of sectors (0 through 8). The sector protection feature is enabled using programming
equipment at the user’s site. The device is shipped with all sectors unprotected.
To activate this mode, the programming equipment must force V
ID
on address pin A
9
and control pin OE, (suggest
V
ID
= 11.5 V) and CE = V
IH
. The sector addresses (A
18
, A
17
and A
16
) should be set to the sector to be protected.
Table 4 defines the sector address for each of the eight (8) individual sectors. Programming of the protection
circuitry begins on the falling edge of the WE pulse and is terminated with the rising edge of the same. Sector
addresses must be held constant during the WE pulse. See figures 11 and 17 sector protection waveforms and
algorithm.
Table 3 MBM29F040C Sector Protection Verify Autoselect Codes
Type
A
18
A
17
A
16
A
6
A
1
A
0
Code
7
DQ
6
DQ
5
DQ
4
DQ
3
DQ
2
DQ
1
DQ
0
Manufacture’s
Code
X
X
X
V
IL
V
IL
V
IL
04H
0
0
0
0
0
1
0
0
Device Code
X
X
X
V
IL
V
IL
V
IH
A4H
1
0
1
0
0
1
0
0
Sector
Protection
Sector
Addresses
V
IL
V
IH
V
IL
01H*
0
0
0
0
0
0
0
1
Table 4 Sector Address Tables
Sector Address
A
18
A
17
A
16
Address Range
SA0
0
0
0
00000H to 0FFFFH
SA1
0
0
1
10000H to 1FFFFH
SA2
0
1
0
20000H to 2FFFFH
SA3
0
1
1
30000H to 3FFFFH
SA4
1
0
0
40000H to 4FFFFH
SA5
1
0
1
50000H to 5FFFFH
SA6
1
1
0
60000H to 6FFFFH
SA7
1
1
1
70000H to 7FFFFH
相關PDF資料 |
PDF描述 |
|---|---|
| MBM29F040C-55 | Replaced by TPS2041B : 0.7A, 2.7-5.5V Single Hi-Side MOSFET, Fault Report, Act-Low Enable 8-PDIP -40 to 85 |
| MBM29F040C-55PD | 4M (512K X 8) BIT |
| MBM29F040C-55PFTN | Replaced by TPS2041B : 0.7A, 2.7-5.5V Single Hi-Side MOSFET, Fault Report, Act-Low Enable 8-SOIC 0 to 85 |
| MBM29F040C-55PFTR | Replaced by TPS2041B : 0.7A, 2.7-5.5V Single Hi-Side MOSFET, Fault Report, Act-Low Enable 8-SOIC 0 to 85 |
| MBM29F040C-70 | Replaced by TPS2041B : 0.7A, 2.7-5.5V Single Hi-Side MOSFET, Fault Report, Act-Low Enable 8-SOIC 0 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MBM29F040C-55 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:4M (512K X 8) BIT |
| MBM29F040C-55PD | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:4M (512K X 8) BIT |
| MBM29F040C-55PFTN | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY 4M (512K x 8) BIT |
| MBM29F040C-55PFTR | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:4M (512K X 8) BIT |
| MBM29F040C-70 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:4M (512K X 8) BIT |
發布緊急采購，3分鐘左右您將得到回復。