參數資料
型號： MBM29F080AC-90PF
廠商： Fujitsu Limited
英文描述： 8M (1M X 8) BIT
中文描述： 8米（1米× 8）位
文件頁數： 17/47頁
文件大?。?/td> 564K
代理商： MBM29F080AC-90PF
17
MBM29F080A
-55/-70/-90
Write Operation Status
Notes:
1.Performing successive read operations from the erase-suspended sector will cause DQ
2
to toggle.
2.Performing successive read operations from any address will cause DQ
6
to toggle.
3.Reading the byte address being programmed while in the erase-suspend program mode will indicate logic
“1” at the DQ
2
bit. However, successive reads from the erase-suspended sector will cause DQ
2
to toggle.
DQ
7
Data Polling
The MBM29F080A device features Data Polling as a method to indicate to the host that the embedded algorithms
are in progress or completed. During the Embedded Program Algorithm, an attempt to read the device will
produce the complement of the data last written to DQ
7
. Upon completion of the Embedded Program Algorithm,
an attempt to read the device will produce the true data last written to DQ
7
. During the Embedded Erase
Algorithm, an attempt to read the device will produce a “0” at the DQ
7
output. Upon completion of the Embedded
Erase Algorithm an attempt to read the device will produce a “1” at the DQ
7
output. The flowchart for Data Polling
(DQ
7
) is shown in Figure 18.
Data polling will also flag the entry into Erase Suspend. DQ
7
will switch “0” to “1” at the start of the Erase Suspend
mode. Please note that the address of an erasing sector must be applied in order to observe DQ
7
in the Erase
Suspend Mode.
During Program in Erase Suspend, Data polling will perform the same as in regular program execution outside
of the suspend mode.
For chip erase, the Data Polling is valid after the rising edge of the sixth WE pulse in the six write pulse sequence.
For sector erase, the Data Polling is valid after the last rising edge of the sector erase WE pulse. Data Polling
must be performed at sector address within any of the sectors being erased and not a sector that is within a
protected sector group. Otherwise, the status may not be valid.
Table 7 Hardware Sequence Flags
Status
DQ
7
DQ
6
DQ
5
DQ
3
DQ
2
In Progress
Embedded Program Algorithm
DQ
7
Toggle
0
0
1
Embedded Erase Algorithm
0
Toggle
0
1
Toggle
Erase
Suspended
Mode
Erase Suspend Read
(Erase Suspended Sector)
1
1
0
0
Toggle
(Note 1)
Erase Suspend Read
(Non-Erase Suspended Sector)
Data
Data
Data
Data
Data
Erase Suspend Program
(Non-Erase Suspended Sector)
DQ
7
Toggle
(Note 2)
0
0
1
(Note 3)
Exceeded
Time Limits
Embedded Program Algorithm
DQ
7
Toggle
1
0
1
Embedded Erase Algorithm
0
Toggle
1
1
N/A
Erase
Suspended
Mode
Erase Suspend Program
(Non-Erase Suspended Sector)
DQ
7
Toggle
1
0
N/A
相關PDF資料
PDF描述
MBM29F080AC-90PFTN Single-Channel Current-Limited Power Distribution Switch 8-MSOP-PowerPAD -40 to 85
MBM29F080AC-90PFTR Single-Channel Current-Limited Power Distribution Switch 8-MSOP-PowerPAD -40 to 85
MBM29F080AC-90PTN Single-Channel Current-Limited Power Distribution Switch 8-MSOP-PowerPAD -40 to 85
MBM29F080AC-90PTR Single-Channel Current-Limited Power Distribution Switch 8-SOIC -40 to 85
MBM29F080AC-55PF M39012 MIL RF CONNECTOR
相關代理商/技術參數
參數描述
MBM29F080AC-90PFTN 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8M (1M X 8) BIT
MBM29F080AC-90PFTR 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8M (1M X 8) BIT
MBM29F080AC-90PTN 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8M (1M X 8) BIT
MBM29F080AC-90PTR 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8M (1M X 8) BIT
MBM29F160BE-55 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8/1M X 16) BIT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*