- 您現在的位置：買賣IC網 > PDF目錄377947 > MBM29LV002TC-70PNS (FUJITSU LTD) 2M (256K x 8) BIT PDF資料下載
參數資料
| 型號： | MBM29LV002TC-70PNS |
| 廠商： | FUJITSU LTD |
| 元件分類： | DRAM |
| 英文描述： | 2M (256K x 8) BIT |
| 中文描述： | 256K X 8 FLASH 3V PROM, 70 ns, PDSO40 |
| 封裝： | PLASTIC, SON-40 |
| 文件頁數： | 13/52頁 |
| 文件大?。?/td> | 436K |
| 代理商： | MBM29LV002TC-70PNS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
13
MBM29LV002TC
-70/-90/-12
/MBM29LV002BC
-70/-90/-12
Write
Device erasure and programming are accomplished via the command register. The contents of the register serve
as inputs to the internal state machine. The state machine outputs dictate the function of the device.
The command register itself does not occupy any addressable memory location. The register is a latch used to
store the commands, along with the address and data information needed to execute the command. The
command register is written by bringing WE to V
IL
, while CE is at V
IL
and OE is at V
IH
. Addresses are latched on
the falling edge of WE or CE, whichever happens later; while data is latched on the rising edge of WE or CE,
whichever happens first. Standard microprocessor write timings are used.
Refer to AC Write Characteristics and the Erase/Programming Waveforms for specific timing parameters.
Sector Protection
The MBM29LV002TC/BC feature hardware sector protection. This feature will disable both program and erase
operations in any number of sectors (0 through 6). The sector protection feature is enabled using programming
equipment at the user’s site. The devices are shipped with all sectors unprotected. Alternatively, Fujitsu may
program and protect sectors in the factory prior to shiping the device.
To activate this mode, the programming equipment must force V
ID
on address pin A
9
and control pin OE, (suggest
V
ID
= 11.5 V), CE = V
IL
, and A
6
= V
IL
. The sector addresses (A
17
, A
16
, A
15
, A
14
, and A
13
) should be set to the sector
to be protected. Tables 4 and 5 define the sector address for each of the seven (7) individual sectors. Programming
of the protection circuitry begins on the falling edge of the WE pulse and is terminated with the rising edge of
the same. Sector addresses must be held constant during the WE pulse. See Figures 13 and 21 for sector
protection waveforms and algorithm.
To verify programming of the protection circuitry, the programming equipment must force V
ID
on address pin A
9
with CE and OE at V
IL
and WE at V
IH
. Scanning the sector addresses (A
17
, A
16
, A
15
, A
14
, and A
13
) while (A
10
, A
6
,
A
1
, A
0
) = (0, 0, 1, 0) will produce a logical “1” code at device output DQ
0
for a protected sector. Otherwise the
devices will read 00H for unprotected sector. In this mode, the lower order addresses, except for A
0
, A
1
, A
6
, and
A
10
are DON’T CARES. Address locations with A
1
= V
IL
are reserved for Autoselect manufacturer and device
codes.
It is also possible to determine if a sector is protected in the system by writing an Autoselect command. Performing
a read operation at the address location XX02H, where the higher order addresses (A
17
, A
16
, A
15
, A
14
, and A
13
)
are the desired sector address will produce a logical “1” at DQ
0
for a protected sector. See Tables 3.1 and 3.2
for Autoselect codes.
Temporary Sector Unprotection
This feature allows temporary unprotection of previously protected sectors of the MBM29LV002TC/BC devices
in order to change data. The Sector Unprotection mode is activated by setting the RESET pin to high voltage
(12 V). During this mode, formerly protected sectors can be programmed or erased by selecting the sector
addresses. Once the 12 V is taken away from the RESET pin, all the previously protected sectors will be protected
again. See Figures 14 and 22.
相關PDF資料 |
PDF描述 |
|---|---|
| MBM29LV002TC-70PTN | 2M (256K x 8) BIT |
| MBM29LV002TC-70PTR | 2M (256K x 8) BIT |
| MBM29LV002TC-90 | 2M (256K x 8) BIT |
| MBM29LV002B | CMOS 2M (256K ×8) Flash Memory(CMOS 2M(256K ×8)位 單5V 電源電壓閃速存儲器) |
| MBM29LV002T | CMOS 2M (256K ×8) Flash Memory(CMOS 2M(256K ×8)位 單5V 電源電壓閃速存儲器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MBM29LV002TC-70PTN | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:2M (256K x 8) BIT |
| MBM29LV002TC-70PTR | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:2M (256K x 8) BIT |
| MBM29LV002TC-90 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:2M (256K x 8) BIT |
| MBM29LV002TC-90PNS | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:2M (256K x 8) BIT |
| MBM29LV002TC-90PTN | 制造商:Fuji Electric 功能描述:NOR Flash, 256K x 8, 40 Pin, Plastic, TSSOP |
發布緊急采購，3分鐘左右您將得到回復。