參數資料
型號： MBM29LV004BC-90PTN
廠商： FUJITSU LTD
元件分類： DRAM
英文描述： 4M (512K X 8) BIT
中文描述： 512K X 8 FLASH 3V PROM, 90 ns, PDSO40
封裝： PLASTIC, TSOP1-40
文件頁數： 3/52頁
文件大?。?/td> 442K
代理商： MBM29LV004BC-90PTN
3
MBM29LV004TC
-70/-90/-12
/MBM29LV004BC
-70/-90/-12
I
GENERAL DESCRIPTION
The MBM29LV004TC/BC are a 4M-bit, 3.0 V-only Flash memory organized as 512K bytes of 8 bits each. The
MBM29LV004TC/BC are offered in a 40-pin TSOP(I) and 40-pin SON packages. These devices are designed
to be programmed in-system with the standard system 3.0 V V
CC
supply. 12.0 V V
PP
and 5.0 V V
CC
are not required
for write or erase operations. The devices can also be reprogrammed in standard EPROM programmers.
The standard MBM29LV004TC/BC offer access times 70 ns and 120 ns, allowing operation of high-speed
microprocessors without wait states. To eliminate bus contention the devices have separate chip enable (CE),
write enable (WE), and output enable (OE) controls.
The MBM29LV004TC/BC are pin and command set compatible with JEDEC standard E
2
PROMs. Commands
are written to the command register using standard microprocessor write timings. Register contents serve as
input to an internal state-machine which controls the erase and programming circuitry. Write cycles also internally
latch addresses and data needed for the programming and erase operations. Reading data out of the devices
is similar to reading from 5.0 V and 12.0 V Flash or EPROM devices.
The MBM29LV004TC/BC are programmed by executing the program command sequence. This will invoke the
Embedded Program Algorithm which is an internal algorithm that automatically times the program pulse widths
and verifies proper cell margin. Typically, each sector can be programmed and verified in about 0.5 seconds.
Erase is accomplished by executing the erase command sequence. This will invoke the Embedded Erase
Algorithm which is an internal algorithm that automatically preprograms the array if it is not already programmed
before executing the erase operation. During erase, the devices automatically time the erase pulse widths and
verify proper cell margin.
Any individual sector is typically erased and verified in 1.0 second. (If already completely preprogrammed.)
The devices also feature a sector erase architecture. The sector mode allows each sector to be erased and
reprogrammed without affecting other sectors. The MBM29LV004TC/BC are erased when shipped from the
factory.
The devices feature single 3.0 V power supply operation for both read and write functions. Internally generated
and regulated voltages are provided for the program and erase operations. A low V
CC
detector automatically
inhibits write operations on the loss of power. The end of program or erase is detected by Data Polling of DQ
7
,
by the Toggle Bit feature on DQ
6
, or the RY/BY output pin. Once the end of a program or erase cycle has been
completed, the devices internally reset to the read mode.
Fujitsu’s Flash technology combines years of EPROM and E
2
PROM experience to produce the highest levels
of quality, reliability, and cost effectiveness. The MBM29LV004TC/BC memories electrically erase the entire chip
or all bits within a sector simultaneously via Fowler-Nordhiem tunneling. The bytes are programmed one byte
at a time using the EPROM programming mechanism of hot electron injection.
相關PDF資料
PDF描述
MBM29LV004BC-90PTR 4M (512K X 8) BIT
MBM29LV004TC-12 4M (512K X 8) BIT
MBM29LV004TC-12PNS 4M (512K X 8) BIT
MBM29LV004TC-12PTN 4M (512K X 8) BIT
MBM29LV004TC-12PTR 4M (512K X 8) BIT
相關代理商/技術參數
參數描述
MBM29LV004BC-90PTR 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:4M (512K X 8) BIT
MBM29LV004T-12PNS-X-EE 制造商:FUJITSU 功能描述:
MBM29LV004T12PNSXR 制造商:FUJITSU 功能描述:
MBM29LV004TC 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:4M (512K X 8) BIT
MBM29LV004TC-12 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:4M (512K X 8) BIT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*