- 您現在的位置：買賣IC網 > PDF目錄377949 > MBM29LV017-12 (Fujitsu Limited) 16M (2M X 8) BIT PDF資料下載
參數資料
| 型號： | MBM29LV017-12 |
| 廠商： | Fujitsu Limited |
| 英文描述： | 16M (2M X 8) BIT |
| 中文描述： | 1,600（2米× 8）位 |
| 文件頁數： | 22/52頁 |
| 文件大?。?/td> | 600K |
| 代理商： | MBM29LV017-12 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
22
MBM29LV017
-80/-90/-12
Notes:
1. Performing successive read operations from any address will cause DQ
6
to toggle.
2. Reading the address being programmed while in the erase-suspend program mode will indicate logic
“1” at the DQ
2
bit. However, successive reads from the erase-suspended sector will cause DQ
2
to toggle.
RY/BY
Ready/Busy Pin
The MBM29LV017 provides a RY/BY open-drain output pin as a way to indicate to the host system that the
Embedded
Algorithms are either in progress or has been completed. If the output is low, the device is busy with
either a program or erase operation. If the output is high, the device is ready to accept any read/write or erase
operation. When the RY/BY pin is low, the device will not accept any additional program or erase commands
with the exception of the Erase Suspend command. If the MBM29LV017 is placed in an Erase Suspend mode,
the RY/BY output will be high, by means of connecting with a pull up resistor to V
CC
.
During programming, the RY/BY pin is driven low after the rising edge of the fourth WE pulse. During an erase
operation, the RY/BY pin is driven low after the rising edge of the sixth WE pulse. The RY/BY pin will indicate a
busy condition during the RESET pulse. See Figure 11 and 12 for a detailed timing diagram. The RY/BY pin is
pulled high in stadby mode.
Since this is an open-drain output, RY/BY pins can be tied together in parallel with a pull-up resistor to V
CC
.
RESET
Hardware Reset Pin
The MBM29LV017 device may be reset by driving the RESET pin to V
IL
. The RESET pin has a pulse requirement
and has to be kept low (V
IL
) for at least 500 ns in order to properly reset the internal state machine. Any operation
in the process of being executed will be terminated and the internal state machine will be reset to the read mode
t
READY
after the RESET pin is driven low. Furthermore, once the RESET pin goes high, the devices requires an
additional t
RH
before it will allow read access. When the RESET pin is low, the device will be in the standby mode
for the duration of the pulse and all the data output pins will be tri-stated. If a hardware reset occurs during a
program or erase operation, the data at that particular location will be corrupted. Please note that the RY/BY
output signal should be ignored during the RESET pulse. See Figure 12 for the timing diagram. Refer to
Temporary Sector Unprotection for additional functionality.
If hardware reset occurs during Embedded Erase Algorithm, there is a possibility that the erasing sector(s)
cannot be used.
Table 8 Toggle Bit Status
Mode
DQ
7
DQ
6
DQ
2
Program
DQ
7
Toggle
1
Erase
0
Toggle
Toggle
Erase-Suspend Read
(Erase-Suspended Sector)
(Note 1)
1
1
Toggle
Erase-Suspend Program
DQ
7
Toggle (Note 1)
1 (Note 2)
相關PDF資料 |
PDF描述 |
|---|---|
| MBM29LV017-12PBT | Circular Connector; No. of Contacts:41; Series:; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:22; Circular Contact Gender:Socket; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:22-41 RoHS Compliant: No |
| MBM29LV017-12PBT-SF2 | Circular Connector; No. of Contacts:41; Series:; Body Material:Aluminum; Connector Shell Size:22; Circular Contact Gender:Socket; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:22-41; MIL SPEC:MIL-C-26482 Series I RoHS Compliant: No |
| MBM29LV017-12PTN | Circular Connector; No. of Contacts:41; Series:; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:22; Circular Contact Gender:Socket; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:22-41 RoHS Compliant: No |
| MBM29LV017-90PBT-SF2 | RP Series - Econoline Unregulated DC-DC Converters; Input Voltage (Vdc): 15V; Output Voltage (Vdc): 24V; Power: 1W; Pot-Core Transformer - separated windings; High 5.2kVDC Isolation in compact size; Optional Continuous Short Circuit Protected; Pin Compatible with RH & RK Series; Approved for Medical Applications; UL and EN Safety Approvals; Efficiency to 82% |
| MBM29LV017-80PTN | HF full bridge driver IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MBM29LV017-12PBT | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8) BIT |
| MBM29LV017-12PBT-SF2 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8) BIT |
| MBM29LV017-12PTN | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8) BIT |
| MBM29LV017-12PTR | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8) BIT |
| MBM29LV017-80 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8) BIT |
發布緊急采購，3分鐘左右您將得到回復。