參數資料
型號： MBM29LV160T-80PFTN
廠商： FUJITSU LTD
元件分類： DRAM
英文描述： CONNECTOR ACCESSORY
中文描述： 1M X 16 FLASH 3V PROM, 80 ns, PDSO48
封裝： PLASTIC, TSOP1-48
文件頁數： 16/60頁
文件大小： 767K
代理商： MBM29LV160T-80PFTN
16
MBM29LV160T
-80/-90/-12
/MBM29LV160B
-80/-90/-12
Write
Device erasure and programming are accomplished via the command register. The command register is written
by bringing WE to V
IL
, while CE is at V
IL
and OE is at V
IH
. Addresses are latched on the falling edge of CE or
WE, whichever occurs later, while data is latched on the rising edge of CE or WE pulse, whichever occurs first.
Standard microprocessor write timings are used. See Figures 6 to 8.
Refer to AC Write Characteristics and the Erase/Programming Waveforms for specific timing parameters.
Sector Protection
The MBM29LV160T/B features hardware sector protection. This feature will disable both program and erase
operations in any number of sectors (0 through 34). The sector protection feature is enabled using programming
equipment at the user’s site. The device is shipped with all sectors unprotected.
To activate this mode, the programming equipment must force V
ID
on address pin A
9
and control pin OE, CE =
V
IL
, A
0
= A
6
= V
IL
, A
1
= V
IH
. The sector addresses pins (A
19
, A
18
, A
17
, A
16
, A
15
, A
14
, A
13
, and A
12
) should be set to
the sector to be protected. Tables 5 and 6 define the sector address for each of the thirty five (35) individual
sectors. Programming of the protection circuitry begins on the falling edge of the WE pulse and is terminated
with the rising edge of the same. Sector addresses must be held constant during the WE pulse. See figures 16
and 24 for sector protection waveforms and algorithm.
To verify programming of the protection circuitry, the programming equipment must force V
ID
on address pin A
9
with CE and OE at V
IL
and WE at V
IH
. Scanning the sector addresses (A
19
, A
18
, A
17
, A
16
, A
15
, A
14
, A
13
, and A
12
)
while (A
6
, A
1
, A
0
) = (0, 1, 0) will produce a logical “1” at device output DQ
0
for a protected sector. Otherwise the
device will read 00H for an unprotected sector. In this mode, the lower order addresses, except for A
0
, A
1
, and
A
6
are DON’T CARES. Address locations with A
1
= V
IL
are reserved for Autoselect manufacturer and device
codes. A
-1
requires to V
IL
in byte mode.
It is also possible to determine if a sector is protected in the system by writing an Autoselect command. Performing
a read operation at the address location XX02H, where the higher order addresses pins (A
19
, A
18
, A
17
, A
16
, A
15
,
A
14
, A
13
, and A
12
) represents the sector address will produce a logical “1” at DQ
0
for a protected sector. See
Tables 4.1 and 4.2 for Autoselect codes.
Temporary Sector Unprotection
This feature allows temporary unprotection of previously protected sectors of the MBM29LV160T/B devices in
order to change data. The Sector Unprotection mode is activated by setting the RESET pin to high voltage (12
V). During this mode, formerly protected sectors can be programmed or erased by selecting the sector addresses.
Once the 12 V is taken away from the RESET pin, all the previously protected sectors will be protected again.
(See Figures 18 and 25.)
相關PDF資料
PDF描述
MBM29LV160T-80PFTY CONNECTOR ACCESSORY
MBM29LV160T-80PN CONNECTOR ACCESSORY
MBM29LV160T-90 CONNECTOR ACCESSORY
MBM29LV200B-10 CMOS 2M (256K×8/128K ×16) Bit Flash Memory(2M (256K×8/128K ×16)位 單5V 電源電壓閃速存儲器)
MBM29LV200T-10 CMOS 2M (256K×8/128K ×16) Bit Flash Memory(2M (256K×8/128K ×16)位 單5V 電源電壓閃速存儲器)
相關代理商/技術參數
參數描述
MBM29LV160T-80PFTR 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M x 8/1M x 16) BIT
MBM29LV160T-80PFTY 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M xⅴ 8/1M x 16) BIT
MBM29LV160T-80PN 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M xⅴ 8/1M x 16) BIT
MBM29LV160T-90 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M xⅴ 8/1M x 16) BIT
MBM29LV160T-90PBT 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M x 8/1M x 16) BIT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*